FASTPRO Cordless SDS Plus Rotary Hammer Drill Kit, 20V Brushless Multifunctional Hammer Drill Driver with 1.5Ah Battery, Including 10PCS Drill Bits & 4PCS SDS-Plus Drill Bits

Why I Reached for This Compact SDS-Plus

I spent a long weekend setting anchors for garage shelving, hanging some patio string-light mounts in stucco, and drilling through a few stubborn blocks that usually make my wrists regret using a standard hammer drill. For those tasks, I wanted something light, simple, and cordless. The Fastpro 20V SDS‑plus rotary hammer fit the brief on paper: brushless motor, two modes (hammer drilling and drilling), a removable adapter for standard bits, and an included starter set of SDS‑plus and HSS bits. After living with it for multiple small projects, here’s how it stacked up.

Design and Ergonomics

At 3.7 pounds with the battery, this is one of the lightest SDS‑plus tools I’ve used. The weight and compact profile matter more than specs alone suggest: reaching overhead or working at arm’s length is far less fatiguing, and I could maneuver into tighter spots than I can with a typical mid‑size rotary hammer. The balance point sits close to the grip, so there’s less nose‑heaviness when you’re starting a hole on slick tile or a painted block.

The two-position mode selector is straightforward—rotate for hammer drilling in masonry or switch to drilling for wood/metal. There’s no chisel-only mode, which is a meaningful design choice: this is a drilling tool first, not a light demolition or chipping solution. The SDS‑plus chuck works as expected; bit changes are quick, positive, and secure.

Build quality is better than I anticipated for a compact kit at this price. Panel fit is clean, the rubber overmold offers decent grip without being gummy, and the selector detents are solid. It’s not built like a pro‑site bruiser, but nothing on it feels fragile.

SDS‑Plus Performance in Masonry

The brushless motor gives this compact hammer more punch than its size implies. In cured concrete, 3/16‑ and 1/4‑inch holes for Tapcons felt fast and drama-free. The bit bites quickly, the tool finds its rhythm, and dust extraction with a simple vac held near the hole kept things tidy. On brick and block, it’s even more composed; you can move quickly without worrying about wandering off your mark.

Stepping up to 5/16- and 3/8‑inch anchor holes, the Fastpro still gets the job done but you do start to feel the limits of a compact SDS‑plus with a small battery. It maintains chips and progress but prefers a measured pace and the occasional back‑out to clear dust. For 1/2‑inch anchors in hard concrete, it’s capable in short stints—think a few holes—rather than an all‑day affair. That’s an expected tradeoff with a light, 20V tool paired to a 1.5Ah pack.

What pleasantly surprised me is how controllable the drilling action is. Some budget rotary hammers feel buzzy and imprecise at hole start; this one settles quickly, tracks straight, and doesn’t transmit excessive vibration back into your wrist. It’s still a rotary hammer—hearing protection and gloves are smart—but the overall feel is more refined than the price would suggest.

Using the Drill/Driver Adapter

The included SDS‑to‑chuck adapter lets you pop in standard, straight‑shank wood and metal bits. In practice, it’s genuinely useful for light crossover tasks. After drilling anchor holes, I drove pilot holes in studs and opened a few holes in sheet metal without swapping tools. The variable speed is easy enough to modulate for clean starts, and the tool isn’t overly bulky for general drilling.

That said, I treat this feature as convenience rather than a replacement for a dedicated drill/driver. If you’re doing a day of cabinetry or delicate work where clutch settings, precise torque, and perfect runout matter, reach for a dedicated drill. But as a “finish this small job without going back to the truck” backup, the adapter earns its keep.

Battery and Runtime

The kit’s 1.5Ah battery is small, and that shows in runtime under heavy load. For a string of small Tapcon holes or light-duty brick work, it’ll cover a modest task list on one charge. Start boring larger holes in hard concrete and the battery becomes the limiting factor quickly. Plan your work in batches and keep a charger nearby, or better yet, pick up a second battery if you anticipate any extended masonry work.

I appreciate how quickly the tool recovers its pace with a fresh battery. The motor doesn’t feel heat-soaked or strained after a few heavy holes; it’s the pack capacity that taps out first. If your workflow involves periodic anchor-setting rather than continuous drilling, the short bursts this setup provides may be all you need.

Vibration, Noise, and Control

Fastpro claims reduced vibration and lower noise with the brushless design. In hand, the vibration damping is respectable for a compact hammer—less tingle through the grip than I usually expect at this price. The tool also feels composed when you lean on it to maintain bit engagement; it doesn’t chatter or dance across the surface. Noise is still very much “rotary hammer loud,” but a touch less shrill than some smaller 12V/18V alternatives.

Trigger control is predictable, which helps when starting holes on tile or in tight quarters. I had good luck easing into porcelain tile with careful alignment and a gentle trigger before allowing the hammering action to take over fully. Again, this is where the light weight helps you keep the bit planted without undue pressure.

Accessories and Bit Quality

The included SDS‑plus bits (1/4, 5/16, 3/8, 1/2 inch) are a useful starter set. They’re not premium carbide by any stretch, but they cut cleanly out of the box. For routine anchors and occasional projects, they’ll get you going; for frequent drilling in tough aggregate, I’d upgrade to name-brand SDS‑plus bits with more robust carbide tips.

The kit also ships with ten HSS bits for wood and metal in small sizes. They’re handy for one‑tool convenience, and the adapter makes quick work of basic drilling. Treat them as consumables—serviceable for light work, but not the bits I’d choose for repeat steel drilling or precision woodworking.

What It’s Not

A few clear boundaries emerged:

• It has only two modes—drilling and hammer drilling—so it’s not for chiseling or light demo.
• The 1.5Ah battery limits sustained heavy drilling. Larger holes in tough concrete drain it fast.
• It’s a compact rotary hammer, not a high‑joule site tool. If you routinely drill deep 1/2‑inch holes all day, you’ll want a bigger hammer and larger battery packs.

None of these are flaws; they’re the tradeoffs that enable the tool’s low weight, approachable size, and price. As long as you match it to appropriate tasks, it performs admirably.

Who It’s For

• DIYers and homeowners who want a real SDS‑plus hammer for anchors, brick/block work, and occasional concrete drilling without lugging a heavy tool.
• Tradespeople who need a lightweight, grab‑and‑go rotary hammer for quick anchor runs, service calls, or overhead tasks, and who already own heavier gear for production work.
• Anyone who appreciates the convenience of switching from masonry to wood/metal drilling with the included adapter to finish small jobs without swapping tools.

If you’re outfitting a crew for daily commercial concrete work, this isn’t your primary. If you’re outfitting a garage, service van, or apartment maintenance kit, it’s a smart, compact choice.

Recommendation

I recommend the Fastpro 20V SDS‑plus rotary hammer for light to moderate masonry tasks where low weight, simple controls, and cordless convenience matter more than all‑day runtime. It shines on Tapcon holes, brick/block anchors, and small batches of concrete drilling. The brushless motor provides smooth, confident progress; the tool is easy to handle in tight spaces; and the adapter adds real utility for quick cross‑material work.

Be realistic about the 1.5Ah battery: it’s a short‑burst power source. If you anticipate frequent or larger‑diameter drilling, budget for an extra battery from the same platform and consider upgrading to premium SDS‑plus bits. Within those boundaries, this compact kit offers a lot of capability for its size and price, and it’s exactly the kind of grab‑and‑go hammer I like having in the shop for everyday anchor and repair tasks.