DeWalt Reciprocating Saw Blade Set (13 pc)

I picked up this DeWalt blade set for a mix of framing demo and light metal work on a rental refresh, and it’s since lived in my truck as my “grab-and-go” assortment. It doesn’t try to be everything for everyone—there are only two tooth patterns here—but what it does include covers a surprising amount of common jobsite cutting without fuss.

What’s in the set

You get 13 reciprocating saw blades and a compact storage case. The assortment breaks down into coarse wood blades and fine-tooth metal blades:

• Wood: 4/6 TPI blades in 6-inch and 9-inch lengths
• Metal: 14/18 TPI blades in 6-inch and 8-inch lengths
• Bi‑metal construction with high-speed steel (HSS) teeth
• Tough-coated finish to reduce friction and gumming

The spread of lengths is sensible. The 6-inch blades keep things controllable for most cuts; the 9-inch wood blades earn their keep for plunge cuts in sheathing and for reaching past trim or siding. The 8-inch metal blade is a nice in-between when 6 inches doesn’t reach, but you don’t want the flex of a 9- or 12-inch blade.

Build quality and fit

These are bi‑metal blades with HSS teeth, which is the proven formula for balancing flexibility and tooth hardness. The shanks fit every standard reciprocating saw I own without slop. The plate thickness is what I’d call middleweight: not as burly as dedicated demolition blades, but stiff enough that I didn’t fight chatter unless I pushed too hard or overhung the blade. The tough-coated finish is more than paint; it noticeably reduces resin build-up when ripping through pine and pressure-treated.

Tooth set is consistent across the pack, and the tips arrive sharp. I didn’t see any tooth brazing defects, and the back edges are deburred well enough that glove snags aren’t an issue.

Wood cutting performance

The 4/6 TPI wood blades are tuned for fast demolition cuts. In clean SPF studs, they bite quickly and clear chips well. On plunge cuts through 1/2-inch OSB, the tip grabs confidently if you start slow and roll in—no need to pre-drill. In nail-embedded lumber, the HSS teeth hold up better than basic carbon steel; I could feel the pace slow once I started hitting galvanized roofing nails, but the blade kept cutting and didn’t immediately round off.

The 9-inch wood blade is the workhorse for remodeling. It’s long enough for cutting double-studs flush to plates and for reaching behind siding to cut old fasteners. You do sacrifice some precision; if you’re trying to follow a line, back off the saw’s orbital action and let the front shoe ride the work. For pruning or green wood, the aggressive pitch works, but these aren’t dedicated pruning blades—expect more vibration and a rougher finish.

If your day-to-day involves clean, finished cuts in hardwoods or trim, this set isn’t the right tool. These are demolition-leaning blades, built to be fast rather than leave a pretty edge.

Metal cutting performance

On the metal side, the 14/18 TPI variable pitch blades handle thin to medium stock well. I used a 6-inch blade to cut EMT conduit, copper pipe, and a handful of 1/4-inch bolts. Starting slow avoids tooth skate, and once the teeth bite, the cut stays controlled. In thin-walled tubing, the variable pitch reduces chatter and the tendency to catch at the exit.

In thicker mild steel—think angle iron or unistrut—the blades make steady progress but do benefit from patience. Use a medium speed, keep steady pressure, and let the teeth clear chips; if you see the blade bluing, back off and give it a break. For stainless or hardened fasteners, expect slower going and more wear. HSS bi‑metal is the right call for general metal cutting, but carbide-tooth blades still outlast these in abusive scenarios.

One pleasant surprise: the 8-inch metal blade is handy when working around brackets or when you need a little extra reach without the whip you get from longer blades.

Control, speed, and cut quality

Overall control is very good for an all-purpose set. The long wood blades do flex when you bury them deep, but the plate has enough stiffness that you can steer through studs and subfloor without the cut wandering wildly. In wood, the kerf stays pretty clean of melted pitch, which I attribute to the coating. In metal, the finish is as you’d expect from a fine-tooth blade—no tearing, just a consistent, slightly burred edge that cleans up quickly with a file.

In terms of speed, the wood blades are fast; the metal blades are reasonably quick in thin stock and deliberate in thicker material. That’s the trade-off for tooth life with HSS teeth. If you’re used to carbide reciprocating blades, the pace here will feel slower, but you’ll also spend less per blade.

Durability and heat management

The HSS teeth hold up well across mixed-material demo. After cutting out a section of stud with hidden nails, I could still rip down the rest of the wall without swapping blades. In metal, tooth rounding is gradual rather than catastrophic. You’ll notice the cut slowing before the blade becomes useless, which gives you time to finish the task.

Heat control is solid for bi‑metal. The coating helps in wood; in metal, it’s more about technique. On long cuts in steel, a touch of cutting oil drops heat and extends life, but it’s optional and messy on a remodel job. Either way, don’t max out the trigger—let the blade do the work, and you’ll get more life out of each.

The case and organization

The included case is compact and tougher than it looks. The latch stays closed in a crowded tool bag, and the internal slots hold blades snugly without bending the tips. It’s easy to see what you’ve got left at a glance, and there’s room to tuck a couple of extra strays from other sets. I do wish the internal dividers were labeled by TPI and length; I ended up marking mine with a paint pen to speed up blade swaps.

What’s missing

This is a focused assortment, and that’s both its strength and its limitation.

• No medium TPI wood blade: A 10–12 TPI general-purpose blade would cover plastics and cleaner wood cuts better than the 4/6 or 14/18.
• No 12-inch option: If you routinely cut deep pockets, reach behind wide fascia, or need flush cuts across larger assemblies, you’ll want a 12-inch blade from another set.
• No carbide teeth: For thick cast iron, nail-saturated timbers, or stainless, a carbide-tooth blade outlasts HSS by a wide margin.

None of these are deal-breakers for general carpentry and light metal work, but they’re worth noting if your work skews heavy demo or industrial.

Who it’s for

This DeWalt blade set makes sense for remodelers, maintenance techs, and DIYers who need a reliable, compact kit that covers the bulk of wood demo and common metal cuts. If your typical day includes pulling out framed walls, trimming pipes, cutting bolts, and slicing through sheathing or siding, this set fits. If you’re primarily cutting finished lumber with visible edges, or your metal work is thick, hard stock, pair this with specialty blades.

Tips for best results

• Use the 6-inch blades whenever possible for better control; jump to 9 inches only for reach.
• In metal, start at a lower speed to avoid tooth skate, then ramp up as the cut establishes.
• Let the shoe stay in contact with the work; it cuts vibration and extends blade life.
• For nail-embedded wood, pause after hitting metal to clear chips and reset your angle before powering through.

Recommendation

I recommend this DeWalt blade set as a solid, go-to assortment for general demolition and maintenance cutting in wood and metal. The bi‑metal, HSS-tooth construction strikes a good balance between speed and longevity, the two tooth patterns cover the most common tasks cleanly, and the included case keeps everything organized in a compact package. It’s not a complete blade library—there’s no medium TPI option, no 12-inch reach, and no carbide—but as a foundation set that you can confidently toss in the bag and rely on day after day, it’s well put together and earns its keep. Pair it with a couple of carbide demolition blades and a 12-inch wood blade, and you’ll be ready for almost anything a reciprocating saw is asked to do on a jobsite.