auxua Wood Grain Peel and Stick Floor Tiles – 11.8” Width, Full Roll Length of 118" – Versatile Design for Any Space, Grey Self Adhesive Vinyl Flooring, Waterproof and Non-Slip Features

Why I tried this peel-and-stick vinyl

I wanted a fast, low-mess way to refresh a small guest bathroom without ripping out tile or wrestling full-size sheet vinyl. Auxua’s peel-and-stick vinyl roll looked like a practical middle ground: wood-grain styling, waterproof surface, and a format that’s easier to store and handle than big sheets or dozens of small planks. I ended up using it in a 25-square-foot powder room and for a small entry threshold where wet shoes tend to gather.

What you’re getting

This is a self-adhesive vinyl “plank” supplied as a roll that’s 118 inches long and 11.8 inches wide (roughly 9.7 square feet per roll). The profile is thin—about 0.02 inches (0.5 mm)—with a textured, non-slip surface and a grey wood-grain print. The roll format matters: it’s much easier to manage in tight spaces than full sheet goods, but each seam runs the full length of the room wherever two strips meet, so precision matters.

The grey tone reads neutral and modern, not blue or brown. The finish is matte with a light grain texture—not plasticky, and it hides dust and footprints better than glossy vinyl.

Installation experience

Prep decides your outcome. I vacuumed, scrubbed, and degreased the tile floor, then wiped with isopropyl alcohol. On deeper grout lines, I skimmed a bit of floor patch to keep the surface as flat as possible; thin vinyl will telegraph dips over time. After a dry layout, I snapped a reference line so the “boards” would track straight.

A few things stood out during installation:

• The roll has memory. Long runs lay flat and bond well, but smaller cutoffs tend to curl. Back-rolling helped. For short pieces, I weighted the corners for an hour or warmed the adhesive lightly with a hair dryer to relax it before pressing.
• Cuts are clean. A sharp utility knife and a metal straightedge were all I needed. The material scores easily and snaps without tearing the face.
• The adhesive feels pressure-activated. It tacks on contact, but really sets when you roll it. A rubber grout float or J-roller makes a difference in getting full bond and pushing air out to the edges.
• Seams are forgiving if you take your time. The factory edges are straight, so butt joints can be nearly invisible. Align the grain before committing, and don’t stretch the strip; stretching leads to gaps later.

Around the toilet and door casing, I templated with kraft paper, transferred the shapes, and cut slightly proud, then trimmed in place. I finished by running a thin bead of color-matched silicone at the tub edge to keep errant splashes from wicking under.

Total time for the powder room: just under three hours, including patching grout lines and cleanup.

Fit, finish, and feel

Once installed, the floor reads more like a wood-look sheet than individual planks, which is unsurprising given the 11.8-inch width. The print is consistent, with a subtle repeat that didn’t jump out in a small space. Underfoot, it’s firm, not cushy—think typical thin vinyl, not foam-backed. The surface texture provides real grip; even with wet feet coming out of the shower, it felt surefooted.

Edges and seams held flush after rolling. Against baseboards, the thin profile tucks cleanly. If you have very uneven transitions, plan on using a reducer or a bead of flexible caulk to make it look intentional.

Performance after use

After several weeks of regular bathroom traffic and a wet, muddy weekend in the entry threshold, here’s how it’s held up:

• Water resistance is solid. Puddles from a splashed bath mat wiped right up, and I didn’t see any water creeping into seams where I had rolled firmly. I’d still seal at tubs and sinks.
• Scuff and scratch resistance are adequate for light to moderate use. Grit from shoes didn’t mark it, and chair feet with felt pads didn’t scar the surface. It’s not a commercial wear layer—you can mar it with a sharp object—so treat it accordingly.
• Adhesion is substrate-dependent. Over the cleaned ceramic tile, long strips stayed put. On a dusty spot I missed near the entry, a short cutoff corner lifted slightly until I cleaned and re-applied with extra pressure. If your subfloor is chalky, priming with a pressure-sensitive primer is a good idea.
• Cleaning is easy. A mild floor cleaner and microfiber mop kept it looking fresh. The matte texture hides small streaks well.

Coverage and value

One roll covers about 9.7 square feet. A typical small bathroom (20–30 square feet) will take two to three rolls depending on your cuts and orientation. For larger rooms, the cost and the number of seams add up quickly; at that point, a click vinyl plank or full sheet may be a better buy and look more cohesive.

Where the Auxua vinyl roll makes the most sense:

• Small spaces: powder rooms, laundry closets, pantries
• Partial coverage: entry mats/thresholds, under-workbench areas
• Renter-friendly refreshes where you want minimal mess and easy removal later

What I liked

• Easy handling: The roll format is genuinely convenient. It’s simple to store leftovers for future patches.
• Clean look in small rooms: With careful seams, it reads as a continuous, modern surface.
• Non-slip texture: Noticeably grippier than many budget vinyls—welcome in wet areas.
• Simple tools: Knife, straightedge, and a roller are enough. No sawdust, no glue buckets.
• Low visual noise: The medium grey plays well with most cabinets and trim without stealing attention.

Where it could be better

• Thin profile shows what’s underneath. Deep grout lines or rough subfloors will print through. Plan on patching and sanding.
• Small pieces need extra persuasion. Cutoffs want to curl; heat and weight solve it, but it takes patience.
• Coverage per roll is limited. Great for small jobs, less compelling for full rooms once you add up rolls and seams.
• Adhesive variability on tricky substrates. On dusty, chalky, or porous surfaces, a primer or supplemental adhesive can save you from edge lift.

Tips for best results

• Let the roll acclimate and relax. Back-roll it for 10–15 minutes before cutting.
• Clean aggressively. Degrease, vacuum, alcohol wipe. A primer helps on porous or chalky floors.
• Pre-fill grout lines and depressions. A thin skim of patching compound prevents telegraphing.
• Roll it firmly. A J-roller or even a rubber float improves bond and seam quality.
• Seal wet edges. Use silicone where the floor meets tubs, showers, and exterior thresholds.
• Plan your seam placement. Keep seams out of direct splash zones and high-wear door swings if you can.

The bottom line

Auxua’s peel-and-stick vinyl roll is an approachable, quick upgrade for small, moisture-prone spaces. It installs with basic tools, looks cleaner than its price suggests in compact rooms, and the non-slip texture inspires confidence around water. Its thin profile and roll memory do demand more prep and technique than the “peel and stick” label implies—especially over tile with pronounced grout lines or when you’re working with short pieces.

Would I recommend it? Yes—for targeted projects. If you’re refreshing a powder room, laundry nook, or entry threshold and want a waterproof, renter-friendly surface you can install in an afternoon, this hits the mark. If you’re covering a large room or need a long-wearing floor for heavy daily traffic, you’ll be better served by thicker click vinyl or sheet goods with fewer seams and a beefier wear layer.