ALLWIN 6 Pack Cabinet Latch - Double Roller Catch Hardware for Cupboard Closet Kitchen Cabinet Door Latches and RV Cabinet, Silver

Why I reached for a simple roller catch set

Old cabinets have a way of reminding you they’re still around—usually by drifting open at the worst time. I wanted a no-fuss way to keep a few inset doors in check without swapping hinges or adding visible hardware. That led me to the ALLWIN roller catch set, a six-pack of spring-loaded double-roller latches with matching strikers and screws. I’ve used plenty of this style over the years; they’re a hardware staple. What matters is whether they install cleanly, hold reliably, and stand up to daily use. After installing these across a few cabinets and a pantry pair, here’s how they stacked up.

What’s in the box

You get six complete latches (roller base + striker) and a small pile of screws in a tidy case. The latch body is nickel-plated steel with nylon rollers; the striker is a simple stamped tab. The head of the latch pivots slightly, which helps with imperfect alignment. It’s a classic layout that’s compatible with most face-frame or frameless cabinets where a tab can meet a roller.

Installation experience

On a set of older inset cabinet doors, installation was straightforward:

• I held the roller base to the frame, closed the door to gauge the meet, and marked the outline.
• A quick pilot with a 1/16-inch bit made life easier, especially in hardwood frames.
• I mounted the base, then positioned the striker on the door edge so it centered between the rollers on close.
• Fine-tuning was just a matter of nudging either part a millimeter or two to balance the closing force.

A couple of practical notes:
- The included screws are adequate for most cabinet stock, but on thicker face frames I swapped to 3/4-inch #6 pan-heads for a more confident bite.
- The steel on the striker and base is on the thin side. If you drive the screws with a high-torque drill or angle the screw in, you can torque or tweak the parts. A hand screwdriver for the final snug-down avoids that.
- The swiveling head on the latch buys you some forgiveness if your door or frame isn’t perfectly square.

On a pantry with light double doors, I paired one latch high and one low per door to keep racking at bay. That provided a reassuring, even hold and cured the “ghost opening” during temperature swings.

Fit and compatibility quirks

Replacing existing roller catches is where tolerances start to matter. On an older catch pattern I had, the original striker’s mounting holes were a touch wider than these. That meant the new striker didn’t land on the old holes. I had three choices: reuse the old striker, open the holes slightly, or drill new ones. Drilling new holes was simplest and resulted in a better-aligned strike, but if you’re trying to drop these into legacy holes, expect a bit of negotiation.

In fresh installs, everything lined up as expected. For overlay doors, you’ll want to check that the striker tab can reach the rollers without rubbing the face. The pivoting head helps, but it’s not a substitute for thoughtful placement.

Build quality and materials

These are made from nickel-plated steel with nylon rollers. The plating is clean, edges are deburred, and the rollers are consistent with a modest spring rate. The gauge of steel isn’t heavy; it’s appropriate for light to medium cabinet doors but not something I’d use on a heavy solid-core closet. If you lean on the striker during install, it can flex—easy to bend back, but worth avoiding in the first place.

In day-to-day use, the nylon rollers ride quietly. There’s the familiar “click” on close, but it’s soft rather than metallic. The springs are not overly stiff, which is good for ease of opening but means you rely on cabinet alignment to maintain a tight hold. A dab of wax on the striker edge made the first few cycles smoother; after a week, the nylon settled in and the action felt more fluid.

Performance over a few weeks

Across the test doors, the ALLWIN catches did what I needed them to do: hold doors shut without making them harder to open. On the pantry pair, the dual-latch setup kept the doors aligned and shut firmly. On inset bedroom cabinets, one latch per door sufficed; the hold felt secure but not childproof, which was my goal.

I also tried one on a small camper galley door. After a weekend on bumpy roads, the door stayed closed without the latch loosening or the striker deforming. For RV or trailer use, I’d still use two on wider doors or those with heavy contents, but for small compartments this style is a solid fit.

Noise is minimal. The nylon rollers eliminate the squeak you sometimes get with old metal-on-metal catches. Closing force is easily adjustable by shifting the striker deeper into the roller cradle or backing it off slightly if you find the pull too strong.

Where the ALLWIN catches excel

• Quick upgrades: For cabinets that occasionally walk open, this is a clean, nearly invisible fix.
• Light to medium doors: Pantry, closet, and built-in cabinets are the natural home for these.
• Slight misalignments: The swiveling head forgives small variances; you don’t need joiner-level precision to get a smooth close.
• Budget-conscious multi-door jobs: A six-pack goes a long way in a kitchen refresh or a basement storage build-out.

Where they fall short

• Thin-gauge hardware: Over-tightening can tweak the parts. Install with a light touch.
• Screw length: In hardwoods or thicker frames, the included screws are on the short side. Have longer #6 pan-heads handy.
• Retrofit to older hole patterns: Don’t count on the striker matching legacy hole spacing. Plan to drill new pilot holes or reuse the old striker if alignment is perfect.
• Heavier doors: For heavy solid wood doors or high-use closet entrances, consider a ball catch with a stronger spring or a magnetic catch with a larger pull.

Tips for a clean install

• Mark with the door closed. Blue tape on the frame makes alignment marks easy to see.
• Always pilot in hardwood. It prevents splitting and keeps screws straight, which preserves the shape of the thin brackets.
• Hand-tighten the last few turns. It’s the best way to avoid bending the base or striker.
• Adjust, don’t force. If the door takes a hard push to close, move the striker out by a millimeter rather than relying on the spring to compress excessively.
• Double up on tall doors. One latch at the top and one at the bottom prevents twist and keeps the reveal even.

Durability outlook

After a few weeks, the springs are consistent and the plating shows no scuffs or corrosion. I wouldn’t classify these as heavy-duty, but they’re entirely fit for interior cabinets and closets. In damp environments (bathrooms, RVs), the nickel plating and nylon rollers are beneficial, though they’re not marine-grade; I’d avoid direct exposure to moisture.

Value

For a six-pack with hardware, the value is strong. You can outfit a small kitchen or a set of closets without spending much. They’re functionally on par with generic shop varieties, with the small bonus of a swiveling head that made alignment easier in my installs.

Final take and recommendation

The ALLWIN roller catch set is a straightforward, effective solution for cabinets and light doors that won’t stay put. Install is quick if you pilot and hand-tighten, the action is quiet, and the hold is reliable for everyday use. The metal is thin enough to demand a careful install, and you may want longer screws on hand, but those are manageable trade-offs.

I recommend this set for anyone refreshing cabinets, securing pantry doors, or outfitting RV compartments on a budget. If you’re replacing existing catches, be ready to drill fresh pilot holes for the striker. For heavy doors or abuse-prone areas, step up to a beefier catch. For most household cabinetry, though, these ALLWIN catches do exactly what you want: click shut, stay closed, and open without a fight.