Skil Folding stand

Why I reached for this stand

I spend a lot of time moving a compact table saw in and out of the truck, onto sidewalks, and across uneven subfloors. A stand that’s quick to deploy, stable on bad ground, and easy to store is worth more than a flashy spec sheet. Skil’s folding stand checks most of the practical boxes I care about, especially if you’re running the brand’s 8-1/4 in worm drive table saw. After several weeks of jobsite and shop use, here’s how it held up.

Setup and first use

There’s almost no learning curve. The stand unfolds with a simple action, the legs lock positively, and the saw attaches with tool-less latches. I didn’t need a bag of bolts, adapters, or a helper. The latches are intuitive: set the saw on the rails, seat it square, flip the latches, and give the saw a shake to confirm it’s locked. Removal is just as quick, which matters when you’re breaking down a site at the end of the day.

Out of the box, the stand was square and true. The leg geometry is sensible—wide enough for stability without hogging floor space. The rubber feet found grip on concrete, plywood, and asphalt without skittering.

Fit and compatibility

This stand is built specifically around Skil’s portable 8-1/4 in worm drive saw (SPT99T). The interface feels purpose-built rather than universal, which I appreciate: no slotted plates or awkward brackets. The result is a tight fit with zero wobble once latched. If you’re hoping to use it with other saws, plan on some ingenuity; it’s not intended as a universal platform.

Portability and storage

At roughly 14 pounds, it’s refreshingly light for a metal stand. Folded, it goes nearly flat and slides cleanly behind a truck seat or against a shop wall. There’s no wheel kit or rolling feature—this is the minimalist “carry it and go” approach—so the low weight matters. I had no trouble carrying it in one hand while the other hand wrangled the saw.

The folding mechanism doesn’t pinch fingers if you use it sensibly, but like any scissor-style stand, keep your hand placement deliberate. The leg locks engage with a reassuring snap and didn’t loosen over time.

Stability and leveling

Every stand makes promises; the real test comes on ugly ground. The adjustable leveling leg is the reason I kept grabbing this stand for remodel work. It has enough travel to deal with dips, patio grades, and old plank floors. Once set, it stayed put; no slow creep or settling during cuts. I did a day of ripping 2x material and sheet goods, and the stand felt planted throughout—no shimmy, even during long rips where you’re leaning on the stock.

The frame flex is minimal for something this light. There is a bit of expected give if you really reef on the saw, but not enough to affect cut quality or confidence. I also like that the foot pads compress slightly, which helps absorb micro movement and keeps the saw from walking during aggressive rips.

Latches and user experience

The tool-less latches are the standout feature in daily use. They engage cleanly and provide a solid mechanical lock without fuss. I checked them repeatedly out of caution the first few days and eventually stopped worrying—no surprises, no sudden releases.

Two practical tips that made life easier:
- After your first setup, mark the rail position relative to the saw base with a paint pen. Your repeat setups go from quick to automatic.
- Give the latches a periodic wipe to keep dust from building up; they stay smoother that way.

If you transport the saw and stand together, a simple strap around the folded package keeps everything compact and stops any rattle in the truck.

Materials and durability

The stand is steel, finished with a durable coating. That choice keeps the price and weight in check while offering the stiffness you want under a table saw. My sample arrived with clean welds and no slag or sharp edges. After being dragged across concrete and tossed into a pickup bed, the finish shows a few honest scuffs but nothing beyond cosmetic. On wet mornings or damp sites, I didn’t see any flash rust; still, if you live on the coast or store gear in a humid trailer, a light coat of paste wax or a corrosion inhibitor on the legs is cheap insurance.

The hardware feels appropriately sized—no undersized fasteners or flexy hinge tubes. I didn’t baby it, and it handled the abuse without developing play.

Ergonomics and working height

The working height hits a practical middle ground. I’m average height and could feed sheet goods without hunching, and shorter crew members weren’t reaching uncomfortably high. It’s a fixed height, though, so if you’re particular about matching outfeed tables or tailgates, you’ll need to adapt downstream support rather than the stand itself. The footprint strikes a reasonable balance: wide enough to be safe, compact enough to fit in tight shops or crowded garages.

That said, this is a bare-bones stand. There’s no integrated outfeed, side extensions, or storage hooks. If you need a whole cutting station, plan on separate supports.

On-site performance

Over a handful of jobs, I used the stand on:
- A sloped driveway for exterior trim
- An old pier-and-beam house with spongy floors
- A tight garage shop between tool carts

In each case, the adjustable leg handled the ground without resorting to shims. The saw stayed square, rip fences tracked straight, and the stand didn’t telegraph vibrations back into the cut. The lightweight build paid off during frequent moves—fold, carry, unfold—without the fatigue that comes with heavier rolling carts.

What I’d change

• A second adjustable leg would make setup even faster on really irregular surfaces. One leg is good; two would be great.
• A dedicated carry handle would improve comfort when moving the folded stand around the site.
• A small tether point or integrated strap keeper would help secure the saw to the folded stand for transport.
• If you’re expecting “universal,” this isn’t that. A modular plate system would broaden appeal, though it would also add complexity and weight.

None of these are deal-breakers, but they’re worth noting depending on your workflow.

Who it’s for

• Owners of Skil’s 8-1/4 in worm drive saw who want a purpose-built, compact stand that sets up fast.
• Remodelers and trim carpenters who bounce between locations and value low weight over rolling wheels.
• Small shops where storage space is tight and a flat-folding stand makes organization simpler.

Who should look elsewhere:
- Users who need integrated extensions, outfeed, or a rolling cart solution.
- Folks trying to mount a non-Skil saw without modifications.

Maintenance and small habits that help

• Keep the latch pivots and leg locks free of dust; a quick brush-off goes a long way.
• Touch up deep chips in the coating to avoid long-term corrosion in wet climates.
• Mark your preferred leveling leg setting for common spots in your shop—setup becomes nearly instant.

The bottom line

This folding stand does exactly what a jobsite stand should: it sets up quickly, holds the saw securely, stays stable on uneven ground, and disappears into a slim package when you’re done. The tool-less latches are genuinely useful; the adjustable leg prevents the shim dance; and at around 14 pounds, it’s easy to live with. It’s purpose-built rather than universal, and it’s a simple stand rather than a full workstation—but that simplicity is part of the appeal.

Recommendation: I recommend this stand if you own Skil’s 8-1/4 in worm drive table saw and need a lightweight, compact, and stable platform that’s fast to deploy. It’s a no-drama solution that keeps the focus on the cut, not on coaxing your setup to behave. If you need wheels, universal mounting, or integrated extensions, this isn’t the right fit; otherwise, it’s an easy choice.