BORA Workhorse XT Saw Horses 2 Pack Folding Heavy Duty Adjustable Height Sawhorse Pair with Adjustable Legs, Heavy Duty Saw horse for Contractors Portable Workbench w/Built in Bottle opener PM-3360T

First impressions and setup

Out of the box, the Bora Workhorse sawhorses give off a no-nonsense, jobsite-ready vibe. Steel throughout, clean welds, and a clever single-latch mechanism that drops the legs with a shake. The setup is genuinely quick: flip the latch, let gravity swing the legs down, then press down lightly until the A-frame locks. It’s a satisfying, positive action that’s markedly faster than the multi-latch routines of many folding horses.

One caution up front: keep your fingers clear when folding them back up. The mechanism is strong and fast, and there are a few pinch points near the hinges if you’re careless.

Build and design

The frame is all metal, with a top deck that’s flat enough for sheet goods and sturdy enough for heavy timbers. Height-adjustable legs telescope in 1-inch increments from 30 to 34 inches, giving you a bit of fine-tuning for task or terrain. The latching mechanism uses a single release on the body rather than one on each leg, which keeps setup and takedown simple.

The top includes integrated brackets sized for 2x4s, and they’re pre-drilled. Drop a pair of 2x4s across two horses and you’ve got a solid platform; link more horses to extend the span. There’s even a built-in bottle opener at the end cap—a novelty, yes, but it does work.

One design detail to note: the cross braces that tie the legs into the A-frame are thinner stamped steel with riveted pivots. They do their job, but they’re not as beefy as the rest of the structure, and they’ll be the first place I’d watch for wear over time.

Stability, capacity, and on-the-job feel

In use, the Workhorse feels planted. I pushed, rocked, and leaned on it more than I should have while ripping sheets and supporting a small benchtop planer. No wobble worth mentioning. The published load rating (1,350 lb per horse, 2,700 lb per pair) is more than I’m likely to approach, but it inspires confidence when stacking and clamping heavy materials.

The feet offer enough surface area to stay put, and the ability to fine-tune each leg helps on uneven slabs or pavers. These aren’t “nonskid” feet, so if you’re on a slick painted floor, a strip of grip tape or rubber mats underfoot is cheap insurance.

Height adjustment and ergonomics

The 30–34 inch range hits a nice sweet spot for most tasks. I tend to set mine at 32 inches for breaking down sheet goods and 34 inches for assembly and sanding—less back strain that way. If you’re very tall or prefer a higher bench, 34 inches may still feel low; that’s a limitation of the format, not the mechanism.

Adjustment is straightforward: pull the leg to the notch you want. To retract, you hit the release inside the leg channel and slide it back up. Two practical notes:
- The release tab is somewhat recessed. Gloves help your grip, and a short flat screwdriver makes it easier if dust or paint builds up.
- Always fully retract the telescoping sections before folding the legs into the body. If a leg is extended even one notch when you close the horse, the leg can bind under hardware from the opposite leg set. If you do jam it, laying the horse on its side and accessing the release through the leg opening will usually free it, but prevention is better.

Portability and storage

These fold down flat and take up surprisingly little space; two slipped behind a shop door barely register. Carrying two at once is doable, though they’re not featherweight. The weight is a trade-off for the stability and all-metal construction. There’s no dedicated carry handle, so I grab them at the top rail or by the folded legs. For frequent transport, a short strap or Velcro wrap keeps the legs from flopping when you’re moving fast.

Making a workbench in minutes

The best part of the Workhorse system is how quickly it turns into a functional bench. I keep two 2x4s cut to the same length as a “stretcher set.” Drop them into the receiving pockets, then lay 3/4-inch plywood on top. Add a few screws through the pre-drilled tabs and you’ve got a bombproof temporary work surface that doesn’t rack under clamping pressure.

Practical tips:
- Use sacrificial 2x4s and a replaceable plywood skin. When the top gets chewed up, replace only the skin.
- Mark your favorite leg heights on the inside of the tubes with a paint pen. It speeds repeat setups.
- If you’re breaking down sheet goods, screw a couple of short stops to the plywood to keep sheets from drifting.

Durability notes and small quirks

After multiple setups in the shop and a couple of trips to a client site, the powder coat has shrugged off scuffs well. The leg latches continue to engage positively. Where I’m cautious:
- Cross-brace stiffness: Because those braces are thinner, aggressive lateral loads (e.g., using the horse as a step and pushing sideways) aren’t ideal. Treat them like a support tool, not a scaffold.
- Telescoping leg cleanliness: Sawdust and jobsite grit can make the release tabs sticky. A blast of compressed air and a dry lube on the sliding faces keeps them smooth.
- Pinch awareness: The speed of the leg deployment and the spring in the hinges can surprise you the first time you fold them. Fold with two hands, and don’t hover fingers near hinge lines.
- Thickness of the top rail: It’s solid, but like most metal-top horses, it’s not a sacrificial surface. If you’re cutting, use the 2x4s as your cutting plane.

Comparison to typical alternatives

Versus plastic folding horses, the Workhorse wins on rigidity and load capacity and loses on pure weight. Versus classic wood horses, you get faster setup, adjustability, and easier storage, but you won’t casually screw into the top without planning your sacrificial pieces. Versus other metal foldables, the gravity-assisted single-latch deployment is the standout—it’s faster and simpler, especially when you’re solo and setting up in tight quarters.

Who it’s for

• Carpenters and remodelers who need a portable, rigid platform that can double as a bench.
• DIYers with small shops who want serious capacity without dedicating permanent floor space.
• Anyone working on uneven surfaces who benefits from independent leg adjustment.

Who might look elsewhere:
- Users who want a higher bench than 34 inches without building risers.
- Folks who need ultra-lightweight portability above all else.
- Anyone averse to maintaining telescoping legs (keep them clean, and they’re great).

The bottom line

The Bora Workhorse sawhorses hit a very usable balance: fast setup, real stability, and practical adjustability, all in a compact package that stores easily. The integrated 2x4 brackets turn two horses into a workstation in minutes, and the load rating is generous enough that I never second-guess what I’m stacking on them.

They aren’t perfect. The telescoping leg releases are slightly recessed, and if you try to fold the horses with a leg extended, you can create a frustrating bind. The cross braces, while adequate, are the lightest-duty element of an otherwise robust build. And at their tallest, some users will still want more height for prolonged bench work.

Would I recommend them? Yes. If you want sturdy, compact sawhorses that transform quickly into a stable workbench and won’t flinch under real loads, these are a smart buy. Treat the leg mechanism with a bit of care, keep the sliding parts clean, and they’ll reward you with speed, stability, and versatility that outclasses typical folding horses.