Hohuqeri Corrugated Roofing Panels Galvanized Steel Roof Panels, L60.63×W16.77 Inch Heavy Duty Metal Roof Panels, Roof Protector for Garages, Sheds, Stables and Mobile Homes, Black, 10PCS

Why I picked these panels

I bought a 10-pack of the Hohuqeri panels to roof a small 5-by-8-foot lean-to over my garden tools and firewood. I wanted something light enough to handle solo on a ladder, tough enough to take rain and wind, and clean-looking in black to tie in with the rest of my shed. The panels’ dimensions (about 60.6 by 16.8 inches each, roughly 5 feet long) and galvanized corrugated steel construction checked those boxes at a reasonable price.

What you get

• Ten corrugated galvanized steel panels, black finish
• Each panel: 60.63 x 16.77 inches, about 0.01 inch thick (a light gauge, roughly 30–31 ga territory)
• A bag of 100 screws with plastic washers

The panels arrived straight with a protective plastic film on the faces. The black finish is consistent and glossy with a subtle metallic depth; it reads more “matte satin” in shade and deep black in direct sun. Corrugation is fairly tight and gives the thin sheet some much-needed stiffness.

Installation experience

I installed these over 2x4 purlins at 16 inches on center. Because the panels are thin, tight purlin spacing matters; at 24 inches you’ll get more flex and oil-canning. Here’s what stood out:

• Handling: Very lightweight, easy to lift and maneuver alone. Edges are sharp—gloves are a must.
• Cutting: Straight cuts were clean with straight-cut aviation snips; for longer rips I used a shear. An angle grinder works but leaves hot shards that can burn the coating; not my first choice for painted material.
• Pre-drilling: I pre-drilled to avoid walking screws and to keep fastener lines tidy. The steel drills quickly.
• Overlap: I ran one corrugation of side overlap and about 6 inches of end lap. That keeps water out and helps with stiffness. On a 5-foot run, a single panel length was perfect with a small overhang.
• Fastening: The included screws technically work, but I swapped them for roofing screws with EPDM (neoprene) washers. Plastic washers don’t seal as reliably over time, and on roofs that’s asking for trouble. I fastened at the high crown on every other corrugation at each purlin—more on the eaves and ridge.
• Protective film: The face film protects the finish during shipping, but it was stubborn to remove. Gentle heat from a hair dryer made it peel cleanly without leaving residue. Plan on a bit of time for this step.

With the right prep, the install is quick. I laid the first panel square, snapped lines for fasteners, and worked upslope. For a small roof, the 10-pack was enough with a couple of panels to spare.

Fit and coverage

Raw coverage per panel is roughly 7 square feet (5.05 ft x 1.40 ft). With one-corrugation side overlap and 6-inch end laps, my effective coverage worked out closer to 6.3–6.5 square feet per panel. That puts a 10-pack in the neighborhood of 63–65 square feet of real-world coverage, which aligned well with my lean-to.

Because each panel is only about 16.8 inches wide, you’ll be stitching together quite a few to span wider runs. That’s fine, just remember side laps and screw count add up, and you’ll want extra fasteners beyond the 100 in the box if you follow tighter patterns.

Build quality and durability

These are thin panels. The corrugation gives them surprising stiffness for their gauge, but they will dent if you bump them against a ladder or drop a tool. Handle them like you would a nice appliance panel: carefully. Once fastened, the roof feels solid under hand pressure, and the metal’s springiness helps it hold shape if you’re not spanning too far between purlins.

The galvanized base with a painted topcoat is appropriate for outdoor use. Cut edges are the weak spot on any galvanized sheet; I hit mine with a touch of cold galvanizing spray and a bit of black enamel. That extra minute per cut will pay off in corrosion resistance.

Weather and noise performance

• Rain: Predictably tinny on an uncovered structure, but not dramatically loud. A synthetic underlayment or even a layer of thin foam backer quiets it considerably and mitigates condensation.
• Wind: On a breezy day the panels stayed put with a conservative screw schedule. Use adequate overlap, fasten at the high crown with EPDM washers, and keep purlins tight. For windy sites, add more fasteners and consider foam closure strips under the eaves and ridge.
• Sun/heat: Black gets hot. That’s good for shedding snow and drying quickly; it’s less ideal if you’re shading a seating area where heat buildup matters. The finish has held its color so far without chalking or fading in the short term.

I wouldn’t spec panels this thin for heavy snow loads or exposed, high-wind roofs without beefed-up framing and fastener density. For light-duty structures, they’re right in the pocket.

Finish and aesthetics

If you’re after a clean, contemporary look on a small outbuilding or accent application, the black corrugation looks sharp. I mocked up a backsplash-style wall accent with the extra panels and liked it enough to mount a section in the workshop. The corrugation casts a nice shadow line, and the uniform finish sells the look. Minor cosmetic scuffs are inevitable with thin painted steel; they’re not obvious in black unless you catch them in raking light.

What could be better

• Included screws: The plastic washers are a weak point. EPDM-sealed roofing screws are a better match for exterior work and will save headaches later.
• Protective film: Effective, but slow to remove. Heat helps; still, it adds time to the job.
• Dent resistance: The trade-off for light weight is easier denting. It’s not a quality defect so much as a limitation of the gauge.

None of these are deal-breakers if you set expectations and prep accordingly.

Practical tips

• Lay panels in the same orientation so the side laps shed water away from prevailing wind.
• Snap chalk lines for fasteners; it looks professional and keeps loads even.
• Use foam closures at eaves and high points to block driven rain and bugs.
• Touch up cut edges with cold galvanizing spray and black enamel.
• Don’t overtighten screws—compress the washer just enough to seal without distorting the panel.

Where these panels make sense

• Small sheds, lean-tos, and tool enclosures
• Carports and grill stations with modest spans
• Chicken coops and garden structures
• Interior or exterior wainscoting and wall accents
• Raised garden beds and DIY furniture cladding

If you’re roofing a primary dwelling or dealing with heavy snow and wind loads, you’ll want thicker-gauge panels and a system that includes matching trims, closures, and a published fastening schedule.

Verdict

The Hohuqeri panels are a solid, budget-friendly option for light-duty roofing and cladding. They’re easy to handle, straightforward to install, and look great when buttoned up. The thin gauge means you need to respect span limits and be careful during handling, and I’d replace the included screws with EPDM-sealed fasteners. Expect to spend a little time removing the protective film.

Would I recommend them? Yes—for small structures and DIY projects where light weight, corrosion resistance, and clean aesthetics matter more than heavy-duty impact resistance. They offer good value, install quickly, and deliver a tidy finish. If your project demands higher structural capacity, thicker steel, or long-term weather sealing straight out of the box, step up to a heavier panel system; otherwise, these panels are a smart, cost-effective choice.