DeWalt Rolling Table Saw Stand

First impressions

A good jobsite stand should disappear in use: steady when you’re cutting, simple when you’re packing up, and tough enough to live in a truck. DeWalt’s rolling stand checks those boxes with a straightforward steel chassis, big wheels, and a fold-flat design that favors durability over gimmicks. It’s not a gravity-rise mechanism with a single pedal—to me, that’s part of its charm. There are fewer moving parts, it packs flatter, and it’s easier to trust after months of bouncing between shop and jobsite.

Setup and assembly

Assembly is simple if you’ve put together any steel-frame stand before. The hardware is well organized, and everything lines up cleanly. Plan on 30–45 minutes at a casual pace. I used a 1/2-in socket with the supplied hex key and a small ratchet; a nut driver or 10/13 mm sockets will make it quicker. My advice:

• Snug all fasteners first, square it up on a flat surface, then fully tighten.
• A drop of medium threadlocker on the wheel axle nuts and main pivots is cheap insurance for jobsite use.
• Cycle the folding action a few times before mounting your saw to confirm nothing binds.

The included mounting hardware covers popular DeWalt compact/jobsite saws. If you’re mounting a non-DeWalt saw, an adapter plate is easy: I drilled a piece of 3/4-in plywood to match my saw’s base and used the stand’s existing holes to bolt it up. It’s a 15-minute step that opens the door to a lot of other saws.

Design and build

The frame is thick steel tubing with a simple hinge architecture. It weighs about 31.5 lb bare, which strikes a good balance: substantial enough to feel rigid but still manageable to maneuver by yourself. The footprint is roughly 29.5 x 29.9 in, and it folds to about 8.6 in tall, so it slides along a van wall, into a truck bed, or upright in a closet without hogging space.

The wheels are the right size for a jobsite—large enough to roll over cords, gravel, and the edge of a trailer ramp without the stand feeling tippy. The tires are solid, so there’s no maintenance there. The powder-coated finish is typical DeWalt yellow and black and holds up to scuffs and occasional rain.

This is a two-mode design: roll it like a dolly when folded, then tip it forward to land on four feet when deployed. There’s no intermediate “park” brake or leveling jack, which keeps the mechanism simple. On uneven ground, the feet still find purchase thanks to the geometry; I didn’t need shims to keep it from rocking unless the surface was truly bad.

Portability and storage

With a compact 10-in saw installed (mine weighs roughly 65–70 lb), the combo is undeniably heavier, but the balance is well sorted. The handle height puts your knuckles above most obstacles, and the wheels let you pull it up a ramp or the lip of a curb without straining. I was able to load it into a trailer solo. For pickup beds, tilting the wheels onto the tailgate and walking it in backwards keeps the weight on the wheels and off your back.

Storage is where this stand wins me over. Folded with the saw attached, it stands on end without drama and occupies a very slim profile. If you’re tight on floor space, that matters. I also like that the folded package doesn’t splay open in transit; the latch is positive and easy to trust.

Stability and daily use

Once upright, the stand feels planted. There’s minimal fore-aft flex when ripping, and lateral racking is well controlled—exactly what you want to keep a portable saw from walking or buzzing under load. I tried it on plywood subfloor, compacted gravel, and in the shop on concrete. The feet distributed the weight evenly, and I didn’t find myself chasing the saw mid-cut.

There’s no height adjustability, so you live with a fixed working height, which in practice feels right for a typical benchtop/jobsite saw. If you often pair your saw with an outfeed table, you may need to adjust the outfeed rather than the saw height. That’s a trade-off I can live with for a stiffer frame and fewer failure points.

The folding action is a one-person job. Pull the latch, tip, and the frame collapses smoothly without pinching fingers or needing a foot pedal. In bad weather or at the end of a long day, those small ergonomics details matter.

Compatibility and mounting

Out of the box, it’s set up for DeWalt’s DWE7490X, DWE7491RS, DWE7499GD, DWE7480, and DW745. I mounted a non-DeWalt compact saw using a plywood plate, and it worked perfectly. The key is to keep the saw’s weight centered over the stand’s main cross members; if you’re off by much, the combo can feel nose-heavy when you tip it back to roll. A quick test-fit before final bolting saves hassle.

If you frequently swap saws, consider using threaded inserts in your adapter plate and a set of knurled knobs. You’ll lose a bit of rigidity compared to bolting through steel, but the convenience gains are real.

Durability and maintenance

Steel tubing, solid wheels, and a simple hinge give this stand a long runway. I’d periodically check:

• Axle and hinge fasteners after the first few trips.
• The latch mechanism for debris; a shot of dry lube keeps it crisp.
• Feet for wear if you habitually set up on rough concrete.

I dragged mine across gravel, up a trailer ramp, and in and out of the shop. The finish scuffed as expected, but there’s no functional damage. Nothing rattled loose, and there are no plastic structural parts to crack.

The stand carries a 1-year limited warranty. It’s not a lifetime policy, but given the build, I’d be surprised to need it unless a latch or wheel arrived out of spec.

What could be better

• Instructions are thin. Assembly is still straightforward, but a clearer diagram would shave a few minutes and some head-scratching for first-timers.
• Not a gravity-rise mechanism. If you want a one-pedal up/down routine multiple times a day, you’ll find this slower. The upside is fewer moving parts and a flatter fold.
• Fixed height. If your workflow depends on matching specific outfeed heights without adjusting the outfeed itself, note this limitation.
• No integrated storage. There’s nowhere to stash a miter gauge or push stick on the frame. That’s common for stands, but still a miss for some users.

Who it’s for

• Jobsite carpenters and remodelers who want a tough, simple rolling base with a small folded footprint.
• Small-shop woodworkers juggling limited space; the stand lets the saw live vertically and roll out only when needed.
• Anyone loading a saw solo into a truck or trailer—the wheel size and balance make a noticeable difference.

If you work exclusively in a shop and never move your saw, a fixed cabinet or custom base will be stiffer and can integrate storage. If you’re constantly setting up and breaking down dozens of times a week, a true gravity-rise stand might save a bit of time. For most users in between, this design hits the sweet spot.

Practical tips from use

• Mounting a non-DeWalt saw: use 3/4-in plywood as an adapter, oversize the holes for a bit of alignment wiggle, then tighten firmly.
• Find the balance point. Before final mounting, lift and roll the combo to ensure it feels neutral when tilted back.
• Strap it for transport. Even with a secure latch, I like a light ratchet strap around the folded saw/stand when bouncing around in a trailer.
• Periodic check: after a week of use, retighten the main fasteners and axle nuts; they settle in.

Recommendation

I recommend the DeWalt rolling stand. It’s a sturdy, no-nonsense platform that keeps a jobsite saw portable without introducing fussy mechanisms, and it folds flatter than most alternatives. The big wheels and balanced geometry make loading and rolling easy, stability under cut is excellent for a compact frame, and the steel build should handle years of site abuse. The instructions could be clearer and the fixed height won’t suit every setup, but those are small trade-offs for the reliability and simplicity you get here. If you value a tough stand that stores slim, rolls smoothly, and just works, this is a smart choice.