Generic Throwerblade Snowplow Kit with (Blade, and Hardware Included) – Heavy-Duty Snow Plow Blade - Quick & Efficient Snow Removal - Snow Plow Attachment for Snowblowers- 22 to 32-inch 2-Stage and 3 Stage

What this attachment aims to do

The Throwerblade kit is a simple idea executed with a fair amount of adjustability: turn a 2- or 3‑stage snowblower into a small plow by hanging a blade off the auger housing, then use pins to set angle and lift. In practice, that means faster clears when accumulation is light to moderate and the snow is dry or slushy, without constantly clogging an auger chute or dusting yourself in powder. I tested it through a handful of mid‑winter events on a 24-inch, two‑stage Ariens and a neighbor’s 28‑inch Craftsman, on both concrete and compacted gravel.

Installation: straightforward, but measure your own machine

Out of the box, you get the blade, side brackets that tie into the auger housing, and hardware. You will be drilling into the side panels of your blower to mount the brackets; there’s no way around that. The instructions give a reference dimension for where the pivot arms should land, but tolerances vary a bit by brand and by year. I had better luck dry‑fitting the assembly, marking where the arms naturally contact the housing, then centering my hole layout from those marks. That kept the lift and angle pins sitting square and prevented the blade from binding at either extreme.

On the 24-inch Ariens, I ran into two wrinkles:
- The auger shaft stub protrudes slightly past the side panel. I needed a few spacer washers to push the bracket outboard so it didn’t rub.
- One factory bolt head at the bearing block interfered with the Throwerblade bracket. Swapping to a low‑profile flange bolt solved it.

On the 28-inch Craftsman, the brackets lined up with no interference, but I still used a couple of washers to keep the arms perfectly parallel. In both cases, the included bolts were the right thread and grade, but I grabbed two longer bolts from my shop to accommodate those spacers. Installation time was about 90 minutes on the first machine (measuring twice, drilling once), then around 45 minutes on the second. If you’re comfortable with a drill, center punch, and wrenches, it’s a reasonable Saturday chore.

Two quick notes:
- The spring‑loaded pins for angle and lift depend on hole alignment. If the blade width isn’t set squarely, those pins won’t seat deeply. Take a minute to loosen the crossbar and re-center before tightening everything down.
- If your blower has a bulged “bump‑out” around the auger bearings, have extra washers and slightly longer bolts on hand. It’s an inexpensive insurance policy.

Build quality and design

The blade material feels like a tough, impact‑resistant composite—stiffer than a scoop shovel, with enough flex to survive a hidden ridge in the driveway. After several outings scraping packed powder and pushing wet slush, I saw scuffing but no gouges or cracks. The crossbar and brackets are stout enough that I didn’t notice flex under load, and the pivot points are simple sleeves with pin locks—no cables or linkages to fuss over.

The lift system is manual: you step to the front, pull the blade up a notch, drop a pin, and you’re in “transport” to traverse to your next pass. Angle adjustment is also manual with pins on either side. It’s not a cockpit-adjustable plow, but on a walk‑behind blower that’s acceptable. I prefer the simplicity—fewer parts to freeze up or stretch.

Performance: fast on the right snow, with clear limitations

Where the Throwerblade shines:
- 1–4 inches of light to average‑density snow on flat or gently sloped surfaces
- Slushy accumulations that would choke a chute
- Cleaning long straight runs, like sidewalks or a driveway lane, where you can keep momentum

On a 2.5-inch, slightly wet snowfall, I plowed my 80-foot driveway and two sidewalks in far less time than I would have spent snowblowing. The blade gathers and rolls the snow cleanly when angled a click or two to either side. For powder, I ran it nearly straight to avoid scattering over the top.

Where it struggles:
- Deep, heavy, wet snow (the kind that forms cement at the end of the driveway)
- Steeper grades where traction matters more than engine power
- Broken, uneven surfaces where the blade catches

With about 4–5 inches of saturated snow, my 24-inch blower started to lose traction after 10–15 feet with the blade angled aggressively. That’s not a horsepower problem as much as friction: a wide angled blade builds a wedge that tries to steer you sideways and lighten the rear wheels. Two changes helped a lot: I dropped the blade to a shallower angle and took narrower “bites,” and I added chains to the blower’s tires. With those tweaks, I could keep moving, although pure snowblowing would still have been the better choice for that particular storm.

If you have a track‑drive machine or wheel weights, you’ll be happier in marginal conditions. If not, consider chains; they make a bigger difference than you might expect.

Handling and balance

The kit adds real weight to the nose of the blower. On my Ariens without power steering, that translated to heavier feel at the handles and a larger turning radius, especially with the blade lifted. It’s manageable on flat ground, but in tight spaces you’ll earn your coffee. Machines with trigger steering or tracks compensate nicely. The good news: the front weight helps keep the blade planted when pushing across patches of compacted snow.

The manual lift pins are secure once seated. I tugged on the blade after every adjustment and never popped one loose. I’d still recommend a quick check before you start each session.

Compatibility and adjustability

The Throwerblade is width‑adjustable to match 22–32-inch blowers. I set it to span just a hair wider than the bucket so the blade protects the corners of the housing. Angle adjustment has enough steps to fine‑tune how far you throw to either side. There’s no true “float” feature, so your ground tracking will depend on your blower’s skid shoe height; set those conservatively if you’re on gravel or pavers with proud edges.

If you’re expecting to clear foot‑high banked berms, temper your expectations. This is a helper for the right conditions, not a replacement for a full‑size plow or your blower’s core job in deeper storms.

Tips for best results

• Mock up before drilling: clamp the brackets, cycle the blade through full lift/angle, then mark hole centers.
• Start with a mild blade angle on heavy snow and increase only as traction allows.
• Consider tire chains or weights if your driveway is long or sloped.
• Keep a handful of 3/8-inch washers and a couple of longer bolts handy for machines with bearing bulges or protruding shafts.
• Re‑torque hardware after the first use; the first session will settle everything.

Durability and maintenance

The composite blade shrugged off winter abuse better than I expected. After scraping along rough concrete and catching a heaved seam, it flexed rather than chipping. The pin bores still feel tight. I dabbed anti‑seize on the bracket bolts during install and hit the pins with a spritz of silicone after each use; both habits make cold‑weather adjustments much easier.

Value and costs

Viewed against the cost of an ATV plow or a second machine, the Throwerblade is an economical way to add plowing capability to a blower you already own. It saves real time in the right snow, spares your auger from slush clogs, and stores compactly. Two caveats to factor into cost: you may need a few dollars’ worth of spacers/bolts for a clean fit, and if you’re in the U.S., be aware that cross‑border orders can occasionally generate a separate carrier bill for import/duty fees.

Who it’s for

• Homeowners with 2‑ or 3‑stage blowers facing frequent light-to-moderate snowfalls
• Anyone tired of slush choking their chute
• People with long, straight walkways or driveways where you can keep a steady line

Who should skip it:
- Steep, slick properties without chains, weights, or track drive
- Users expecting to replace their blower for deep, heavy storms
- Very uneven or obstacle‑laden surfaces that will catch a rigid blade

Recommendation

I recommend the Throwerblade for users who understand its sweet spot: light to moderate accumulations, flat to gently sloped surfaces, and a willingness to spend a bit of time getting the install dialed in. It’s well‑built, the adjustability works as advertised once aligned, and it can cut your clearing time dramatically in the right conditions. If your winters lean heavy and wet or your driveway is steep and slick, plan on tire chains and conservative blade angles—or keep your blower ready for the bigger jobs and treat this as a time‑saving accessory, not a replacement.