maycelon Tape Measure Clip Tape Measure Holder Bench Belt Universal Tool with Screws Stainless Steel Tool Hanger Storage Dock for Mount Drill Power Tape Measures and Belt Clips

Why I added these to my shop

My tape measures have a bad habit of vanishing the moment I actually need them. After one too many laps around the bench, I decided to try the Maycelon M6 clips—a set of stainless mounting brackets meant to hold tape measures and any tool with a belt clip. They’re simple: a small stamped bracket you screw to a wooden surface, then drop a tape’s belt clip (or a drill’s) over the lip. No moving parts, no magnets, no fuss. I installed a handful across my bench, tool wall, and the inside of a cabinet door to see if they could tame the clutter.

Design and build quality

Each bracket is stamped from 1 mm stainless steel, which is a good choice for shop environments—resistant to rust and stiff enough to avoid flexing under everyday use. The profile is basic but functional: a flat plate with two screw holes and a folded lip that catches a belt clip. The footprint is compact, so I can tuck them into tight spaces without interfering with other tools.

Because these are stamped, the edges come sharp from the factory. On a few of mine, the outer perimeter and the lip edges were crisp enough to be uncomfortable to the touch. I took a few minutes with a small file and a bit of 220-grit paper to break the corners. That quick pass eliminates any risk of scratching your hand or scuffing a plastic tape case while you’re moving fast at the bench.

The stainless finish is an unobtrusive silver that blends into a shop setting. It’s not polished, not rough—just practical and easy to keep clean.

What’s in the kit

My kit included six brackets, each with two round-head self-tapping screws. The round heads look fine once installed and sit nicely on the bracket’s face. The screws are on the short side. For light duty on softwood, they’re fine; for repeated in-and-out motion or heavier tools, I prefer longer wood screws for more bite. More on that below.

Installation notes

These are dead simple to mount. Here’s what worked well for me:

• Pre-drill pilot holes sized to your screws and wood species. For softwoods and #6 or #8 screws, a 1/16–3/32 inch pilot keeps the wood from splitting and helps the bracket sit flush.
• Aim for studs, thicker plywood, or solid lumber. Avoid drywall or thin sheet goods unless you’re using anchors or backing.
• If you’re planning to hang drills or anything heavier than a tape, swap the included screws for longer wood screws (#8 x 1 in or 1-1/4 in worked great in 3/4 in plywood and studs). The extra length prevents wobble and pull-out over time.
• Consider spacing. I mounted mine about 1–1.5 inches down from the bench top edge so I could drop a tape on without scraping my knuckles.

It’s a five-minute install per bracket, including deburring. Layout is key: I added one at each workstation where I measure often—miter saw, assembly table, and layout bench—plus one inside a cabinet to keep a “clean” tape out of the dust.

Everyday use and performance

The M6 clips do exactly what I wanted: they give my tape measures a consistent parking spot within arm’s reach. The lip engages standard belt clips snugly, and the motion becomes muscle-memory fast—drop it on your way to the next step, grab it without looking when you need it again.

I tested a mix of tapes from compact 16-footers to heavy 25-foot models, all with standard clips. Everything hung securely. The “set and forget” aspect is what I appreciate most; I’m not sliding tapes into tight holsters or fiddling with magnets that attract chips. I’m just docking them and moving on.

These also shine for drills and drivers with belt hooks. A compact impact driver hangs just fine on a single bracket. For full-size drill/drivers or hammer drills, I recommend the longer screws; the bracket itself is strong, but the leverage of a heavier tool can work short screws loose over time.

Beyond that, I’ve used a spare bracket as a catch-all hook for safety glasses by one temple arm and for a small layout pouch with a clip. The slot is friendly to anything that uses a belt clip, so you can improvise storage in places where pegboard doesn’t make sense.

Durability and corrosion resistance

After a few weeks of regular use—including some accidental bumps from boards being maneuvered around the bench—the brackets haven’t deformed. The 1 mm stainless holds its shape well. Stainless is a meaningful upgrade in a shop that sees humidity swings; I’ve had mild steel shop fixtures spot-rust in a season, and that hasn’t been an issue here. Wiping the brackets down during normal bench cleanup is all they need.

The only “maintenance” was that initial edge break. If you skip that step, the brackets will still work, but smoothing the edges makes them feel finished and prevents tiny scuffs on plastic housings.

What they’re best at

• Tape measures: This is the obvious use case, and they excel at it. I’ve installed multiples in my workflow so one is always close.
• Belt-clip tools: Compact drills and drivers hang cleanly. With better screws, even heavier tools feel secure.
• Small clip-on pouches and safety glasses: Handy for the inside of cabinet doors or the side of a rolling cart.
• Tight spaces: The low profile is perfect where a bulky holster would snag.

Limitations and quirks

• Included screws are short: They’re adequate for light duty on softwood, but for longevity—especially with heavier tools—use longer wood screws. It’s a small upgrade that makes a big difference.
• Edges may need a quick deburr: Common with stamped stainless. Two minutes with a file or sandpaper solves it.
• Not for drywall without backing: These are meant to be fastened to wood. If you need them on a sheetrock wall, add anchors or mount to a wood strip first.
• No positive “lock”: This is by design—the tool hangs by its clip. In high-vibration or mobile setups (e.g., a jobsite cart bouncing over thresholds), make sure the clip seats fully or consider a holster with retention.

Value and alternatives

There are plenty of ways to store tape measures: tossing them onto a shelf, sticking them to a magnet strip, or dropping them into a drawer. What these stainless clips offer is consistency and speed without taking up any real space. They’re also easy to distribute around the shop, which reduces wasted steps and keeps your primary tape exactly where your hands expect it to be.

Compared with DIY solutions (a scrap-wood hook, for example), the M6 clips are slimmer, more uniform, and resistant to shop grime and moisture. They won’t swell, crack, or grab splinters. And compared with purpose-built plastic holsters, they’re simpler and less fussy.

Tips for best results

• Swap to #8 x 1–1/4 inch wood screws for high-traffic or heavy-tool locations.
• Deburr the bracket edges before installation.
• Mount them in pairs at workstations: one for your primary tape, one for a second tool like a drill or layout pouch.
• If you’re right-handed, place the bracket slightly to the right of your main stance at each station for quicker grabs.

Final recommendation

I recommend the Maycelon M6 clips, with two caveats: plan to replace the included screws in high-use spots, and take a minute to smooth the stamped edges. Once those minor tweaks are done, they’re a low-cost, low-profile way to keep tape measures and belt-clip tools exactly where you want them. They’ve saved me from countless “where did I set that down?” moments, and their stainless construction holds up well in a real shop environment. If you value quick access and a cleaner bench, these are an easy win.