LOLLY WRAP Made in USA - 8 FT (Watch Installation Video) Adjustable Garage Padded Pole Wrap Lally Column, Basement Pole Wrap Padding, Pole Cushion, Pole Pad, Post Padding, Basketball Support Pole

A cleaner, safer way to tame those basement and garage posts

Support columns are necessary, but they’re not exactly friendly. They ding car doors, collect scuffs, and are a magnet for bumped heads and bruised shins. After trying a few DIY fixes over the years (pool noodles, split foam pipe insulation, even carpet scraps), I installed the Lolly Wrap pole wrap on a garage column and later on two basement lally columns. It’s been a meaningful upgrade: cleaner-looking, sturdier, and more confidence-inspiring than the makeshift options I’ve lived with.

What it is and what you get

The Lolly Wrap is a two-piece adjustable padded wrap designed to cover a single column up to 8 feet tall and up to 16 inches in circumference (roughly a 5-inch diameter). Each kit includes two 4-foot sections that telescope together, so you can cover the height you need without wrestling a single unwieldy sleeve. The exterior is a smooth white vinyl-like skin with a foam core that adds the cushioning. It’s made in the USA and arrives rolled but relaxes quickly.

If your pole is shorter, you can trim the sections with a sharp utility knife and a straightedge. If your pole is taller than 8 feet, you’ll need a second kit. I’d love to see single 4-foot sections offered for those odd heights where you only need another couple of feet.

Installation: straightforward with a few smart tips

The brand points to an installation video, which I watched before starting; it’s worth the two minutes. My first install took about 25 minutes solo, including cleanup. A second set of hands does make alignment fuss-free, but it’s manageable on your own with painter’s tape.

Here’s the approach that worked best for me:
- Measure the pole circumference with a flexible tape. If you’re close to the 16-inch limit, measure again. You want the wrap to close comfortably without straining the seam.
- Dry-fit both 4-foot sections to confirm where they’ll overlap. I positioned the upper sleeve to overlap the lower by about 3 inches so the seam line looked intentional.
- Use small pieces of painter’s tape to tack the foam in place around the pole—three or four points per section are enough. This keeps everything aligned while you deal with the outer skin’s adhesive.
- Start the adhesive seam by peeling back an inch of the liner and folding it outward so you can grab it as you work. Press the vinyl closed at the top, keep tension on the wrap, and slowly pull the liner down while smoothing the seam. A helper makes this step faster, but doing it alone is fine if you go slowly.
- For a snugger look, lightly compress the foam with your hands as you close the seam. On one install I wrapped a single turn of packing tape around the foam before the outer skin; it gave me a crisp finish without affecting the cushioning.

I chose to install the wrap about half an inch off the floor in the garage. That gap keeps the bottom edge clear of water when I rinse the floor and makes cleaning easier. If you prefer it flush, you can add a bead of removable caulk to keep dust out.

Fit and finish

The end result is clean and understated. The white surface offers a smooth, uniform look that blends with painted columns and finished basements. The seam is visible up close, but you can align it to face a wall or least-seen approach. On one column I lined up the seams of the two sections; on another, I staggered them slightly to hide the overlap. Both look tidy.

Because it’s white, it will pick up scuffs from shoes and tires. Most wiped off with a damp cloth; stubborn marks came off with a gentle cleaner or a melamine sponge. The vinyl surface has held up well against incidental bumps. After a few months in a temperature-fluctuating garage, I’ve seen no lifting at the seam or slipping of the sections.

Protection where it matters

The main reason to use a wrap like this is padding, and here the Lolly Wrap does what it promises. It’s firm enough to keep its shape but has enough give to absorb bumps from car doors and kid-height collisions. On my garage post, it’s ended the nagging “don’t swing the door too hard” routine. In the basement, a shin-level bump that used to leave a mark now gets a shrug.

I wouldn’t call the padding “gym-mat thick”—and that’s the point. The profile is slimmer and more finished than the bulky covers you see on outdoor basketball hoops. It reads as part of the column rather than a protective add-on, which is a big part of the appeal in finished spaces.

Durability and maintenance

Between a high-traffic garage and a play-heavy basement, the wraps have been regularly tested. The adhesive seam remains tight, even in a humid summer and a cold snap. The foam hasn’t compressed into flat spots; it springs back after pressure. Occasional tire rubs and soccer ball hits haven’t marred the surface beyond cosmetic scuffs that wipe off.

Two small tips to improve longevity:
- Keep the bottom edge slightly off the floor if you hose or mop regularly. Standing water and grit are the enemy of any edge seam.
- If your pole has surface rust or flaky paint, wire-brush and wipe it clean before installing. The wrap goes on easier and adheres more evenly over a clean surface.

Sizing notes and compatibility

• Height: Two 4-foot sections cover up to 8 feet. If your column is shorter, you’ll trim. If it’s taller, you’ll need an additional kit.
• Circumference: Up to 16 inches. Measure carefully. For smaller poles (like 3-inch steel columns), you’ll have plenty of overlap; the seam still closes neatly.
• Color: White only. I’d like to see a few neutral options (gray, black) for garages and playrooms where scuffs are inevitable.

How it compares to DIY and other options

I’ve used foam pipe insulation and zip ties, wrapped columns in EVA foam sheets, and even tried off-the-shelf hoop pads adapted for indoor use. Those solutions are cheaper, and if budget is the priority, they can work in a pinch. But they either look cobbled together, take longer to fabricate cleanly, or end up bulkier than I want in tight spaces.

The Lolly Wrap earns its premium on three fronts:
- A finished look that blends in, not screams “safety pad.”
- A two-piece, telescoping design that simplifies installation and alignment.
- A balance of firmness and give that protects without puffiness.

If you’re finishing a basement or want a garage to feel organized rather than improvised, the fit-and-finish difference is noticeable.

What could be better

• Price. It’s on the higher side for what appears, at first glance, to be “just foam and vinyl.” The execution and finish do justify it, but budget-minded users may balk.
• Limited colors. White is versatile but not always forgiving.
• Sizing flexibility. Selling single 4-foot sections would be welcome for 9–10 foot columns or partial-height protection on multiple posts.

Who it’s for

• Homeowners who want clean, low-profile impact protection around structural columns.
• Families turning a basement into a play space and looking to minimize injury risk without turning it into a gym.
• Anyone seeking car-door protection around a garage post without resorting to chunky hoop pads or taped-on foam.

If you’re outfitting commercial or heavy-duty applications where repeated hard impacts are expected, a thicker, purpose-built pad may be more appropriate. For residential garages and basements, this strikes the right balance.

Recommendation

I recommend the Lolly Wrap. It’s easy to install, looks polished, and provides meaningful protection against the everyday bumps that make columns such a nuisance. The two-piece design is thoughtfully executed, the finish holds up, and the profile is slim enough to feel like part of the space rather than a workaround. While the price and color options leave room for improvement, the overall experience—especially in finished or semi-finished areas—makes it a worthwhile upgrade over DIY pads and bulkier covers.