DeWalt Touchscreen Cut Gloves With Dyneema Diamond Technology

Why these gloves earned a spot in my rotation

I put the DeWalt touchscreen cut gloves through several weeks of mixed use—sheet-goods handling in the shop, light metal fabrication, a couple of afternoons running trim screws and hanging brackets, and some quick maintenance on a truck. They’ve settled into that sweet spot I look for in everyday work gloves: protective enough for common hazards, dexterous enough to handle small fasteners, and comfortable enough to forget I’m wearing them. They’re not perfect, but they’re thoughtfully designed and honest about what they are.

Fit and comfort

The 13‑gauge knit shell strikes a nice balance between snug and breathable. The knit cuff sits flat under a watch and doesn’t snag on sleeves. I appreciate that the shell is steel- and fiberglass‑free—no itchy fibers poking through after long days. Out of the package, the fit felt true to size with a stretch that hugs the hand without pinching. Finger length is well-proportioned; I can pick up a single drywall screw from the floor without “fishing” with extra fabric at the fingertips.

If you’re used to bulky, high-cut-level gloves, these will feel refreshingly nimble. If you’re coming from thin nitrile disposables, you’ll notice the knit bulk—but you’ll also notice you can stop worrying about incidental nicks.

Cut protection and what the ratings mean

These are rated ANSI/ISEA 105 Cut Level A3, which realistically places them in the “light-to-moderate cut hazard” category. That’s appropriate for material handling, sheet metal with dressed edges, light fab, automotive trim, and general construction. I tested by dragging the palm across the trimmed edge of 26‑gauge HVAC duct and handling freshly ripped laminate; both are situations where bare hands can get sliced. The gloves shrugged off those tasks without drama.

DeWalt also lists EN 388 results at 4/5/4/3 (Abrasion/Cut/Tear/Puncture). Practically speaking:
- Abrasion 4: The palm coating tolerates repeated contact with rough stock and concrete without immediately thinning.
- Cut 5 (coupe test): Good for repeated contact with sharpened but not razor‑grade edges.
- Tear 4, Puncture 3: Decent resistance to snags and brad/splinter pokes, but not a defense against sharp fastener points.

No glove is cut-proof, and these aren’t built for glass handling, demolition with jagged metal, or knife work that demands higher cut levels. For those, step up to A5/A6+.

Grip, feel, and control

The black foam nitrile palm is the standout. Dry grip is excellent—think MDF sheets, painted steel, and plastic bins. On lightly oily fasteners and machine handles, the microtexture still bites well enough to maintain control. I could thread a 10‑24 nut, turn a car battery terminal, and feed thin aluminum through a shear without slipping.

What I like most is the tactile feedback. The coating isn’t overly thick, so I can feel edges, find fastener heads by touch, and start screws without “bulldozing” them. If your work involves manipulating small parts, these hit that “bare-hand precision with added insurance” feeling better than most A3 gloves I’ve worn.

Touchscreen performance

Touchscreen capability can be a gimmick on work gloves; here it’s usable. I could unlock a phone with a passcode, tap to answer calls, scroll through plans, and pinch-zoom on drawings. Small on-screen buttons need a deliberate tap, and swipes at the screen edges occasionally require a second pass. In the field, I often leave one glove on to take photos or punch in measurements—these made that routine frictionless.

Breathability and heat management

Dyneema-based shells are known for high strength-to-weight, and they tend to feel cooler than dense nylon blends. DeWalt claims these help radiate heat away, and in my time with them, they felt cooler and less clammy than many comparable 13‑gauge gloves. On a warm shop day, my hands stayed reasonably dry. They’re not ventilated on the palm (foam nitrile never is), so if your work is constant high-exertion gripping, you’ll still sweat. But for general tasks, they breathe well.

Durability and maintenance

I treat cut‑resistant knits as consumables, but I expect more than a few sessions out of them. After multiple shop days and some abrasive handling—toting OSB, dragging bins, and a lot of screw driving—the palms show light polishing where I grip tools, with no bald spots. The knit shell remains intact, no runs or frays at the fingertips.

One caution: along the side seam near the base of the thumb, I did notice the edge of the foam nitrile beginning to lift slightly after repeated rubbing against a concrete edge and a few knuckle knocks on rough steel. It didn’t tear open, but it’s a reminder that foam coatings can delaminate if abraded at a hard seam or if flexed against sharp corners. Avoid grinding tasks or repetitive scraping against masonry if you want to maximize lifespan.

As for care, the label says hand-wash only. I followed that—mild soap, cool water, air dry flat—and the fit and coating stayed consistent. Machine washing or drying will shorten the life of any foam-coated glove; skip it.

What they aren’t

• They’re not insulated. In cold weather, your hands will feel it. Layer a thin liner if needed.
• They’re not water resistant. Wet lumber or steady rain will soak the knit. Foam nitrile maintains some grip when damp, but your hands won’t stay dry.
• They’re not high‑cut PPE. If you’re routinely handling knife-sharp edges or doing demolition with jagged metal, choose a glove with a higher ANSI cut rating and possibly a thicker coating.
• They’re not high‑viz. If you need hand visibility for safety protocols, look elsewhere.

Sizing and compatibility

Fit felt true to size with a close, natural contour. If you’re between sizes, I’d size up for longevity; a too‑tight knit can stretch the coating and accelerate wear at stress points. The knit cuff plays nicely with long sleeves and watchbands. I had no issues gripping pistol‑grip drills, impact drivers, or ratchets; the coating doesn’t squeak or slip on typical rubber overmolds.

Use cases where they shine

• Material handling: Sheets of plywood, MDF, aluminum, and drywall carry securely with reduced edge bite.
• Automotive/light mechanical: Good tactile feel for connectors, hose clamps, and fasteners without shredding your knuckles.
• Construction and assembly: Fastener handling, bracket installation, and tool operation with reliable grip.
• Metal fab (light): Handling cut stock with dressed edges, operating shears and brakes, and deburring—so long as you’re not dealing with razor edges all day.

A few practical tips

• Rotate pairs. If you wear them daily, alternating between two pairs helps the foam rebound and dry thoroughly, extending life.
• Respect the cut rating. A3 is protective, not invincible. Don’t test them with knife blades or broken glass as if they’re A6s.
• Clean early, not often. Knock off dust at the end of the day. Hand-wash when truly dirty to preserve the foam.
• Watch the seams. If your tasks involve repeated scraping along a single edge (masonry, rough steel), change your grip or add a sacrificial glove for that operation.

The bottom line

The DeWalt touchscreen cut gloves hit a very usable balance: credible cut protection, excellent dry grip, real dexterity, and comfortable, itch‑free wear. The touchscreen function is genuinely helpful, not an afterthought. Breathability is better than many peers, and the fit encourages you to actually keep them on—often the difference between protected and injured hands.

Durability is good for their class, though the foam coating—like all foam coatings—is the limiting factor. Avoid repetitive abrasion on sharp corners, hand-wash only, and you’ll get solid service life. If your work demands higher cut ratings, water resistance, or winter insulation, this isn’t your glove. For general shop, light fab, construction, and automotive tasks, it’s right in the pocket.

Recommendation: I recommend these gloves for tradespeople and DIYers who need everyday A3 cut protection with strong grip and real dexterity, plus the convenience of using a phone without removing gloves. They’re comfortable, practical, and honest about their limits. If you respect those limits and care for them properly, they’re easy to keep in your kit and on your hands.