Franklin Brass Self-Closing 22' Drawer Slides Bottom Mount, 5-Pairs (10-Pieces) Cabinet, 50lb Capacity White Drawer Hardware D68822K-W-B

What you’re actually getting

I installed this 22-inch bottom-mount slide pack from Franklin Brass across a five-drawer bedroom dresser that had seen better days. The first thing to understand is the bundle size: it’s five pairs, which equals 10 pieces. Each drawer needs a left and a right slide, so this kit covers five drawers total. If you’re planning a larger project, plan your quantity accordingly.

Inside the box were the slides, a bag of mounting screws, and printed instructions. The slides have a white epoxy finish, typical of classic roller-style bottom mounts. They’re rated for 50 lb per pair, and they include a self-closing feature that pulls the drawer in during the last inch or so of travel.

Installation experience

If you’ve worked with classic bottom-mount roller slides before, these will feel familiar. The cabinet members mount to the inside of the cabinet, and the drawer members attach to the underside/side edge of the drawer box. I set aside an afternoon and did the whole dresser in one go using a #2 Phillips screwdriver, a drill with a 1/16" bit for pilot holes, a square, and a simple spacer block to keep my slide height consistent.

A few notes from the bench:

• Measure your cabinet depth. These are 22-inch slides; you want your cabinet depth to be at least that deep. If you’re on the cusp, step down a size rather than forcing the fit.
• Standard clearances apply. These bottom-mount slides typically require 1/2" side clearance per side (1" total). If your drawers were already on bottom mounts, there’s a good chance these will retrofit without planing or shimming.
• Handed parts matter. Each pair includes a left and a right. They’re labeled, but it’s easy to mix them up when you’re in a rhythm.
• Pilot holes are worth the extra minute. The included screws bite well, but pilot holes help prevent splitting in softer drawer materials and let you fine-tune alignment.

In my case, the pre-punched cabinet holes lined up neatly with existing screw points, which sped things along. The instructions are basic but sufficient; the important bit is to keep both slides co-planar and parallel. I used a small torpedo level on the cabinet members and checked drawer squareness before committing the screws.

For frameless cabinets like my dresser, mounting is straightforward. If you’re mounting into face-frame cabinets, you may need rear mounting brackets (sockets) to bridge from the slide to the back wall—these aren’t part of this kit, so plan ahead.

Performance and feel

Out of the gate, the slides ran smoothly with the familiar roller-on-track feel. They’re not soft-close; they’re self-closing. That means the last inch engages a small detent and spring action to pull the drawer shut and keep it closed. It’s a positive close with a gentle “snick,” not a damped glide. If you’ve been spoiled by modern soft-close ball-bearing slides, adjust expectations. If you want reliable close without slamming, these do the job.

Load-wise, I tested a couple of drawers around 35–40 lb with hardware, small tools, and household odds and ends. No complaints: they tracked well, didn’t bind, and the self-close still engaged reliably under load. On wider drawers (27–30 inches wide), I could induce a bit of racking when fully extended—that’s typical of this slide style. Keeping drawer boxes square and using quality bottoms (not thin hardboard) minimizes that tendency.

One practical note: like most epoxy/roller bottom mounts, these are about 3/4 extension. If you need true full extension to access the back of deep drawers, a side-mount ball-bearing slide is the better fit. For dressers, utility drawers, and general household cabinetry, 3/4 extension is usually fine.

Build quality and finish

The steel feels appropriate for the weight rating. The white epoxy coating is consistent and helps the slides disappear visually in lighter cabinetry. After installation and several weeks of daily use, I didn’t see premature scuffing, and the rollers stayed quiet. The self-close detent is firm but not aggressive; it didn’t bounce lighter drawers or stall heavier ones.

The included screws are serviceable. If you’re going into particleboard or MDF, consider switching to slightly thicker, coarse-thread cabinetry screws for the cabinet members; they’ll hold better over time, especially on frequently used drawers.

Fit and compatibility

• Size: 22 inches. Don’t try to fudge this dimension—slide length should match the usable cabinet depth behind the face.
• Load rating: 50 lb per pair. That’s typical for this category. For shop drawers loaded with metal parts or tools, consider 100 lb ball-bearing slides instead.
• Clearance: Plan on 1/2" per side. Drawers previously set up for bottom mounts should transition with minimal fuss.
• Color: White. Great for painted or melamine interiors; if you prefer a metallic look or are pairing with exposed hardware, you might want zinc or black-finished alternatives.

Installation tips that made a difference

• Use a spacer block under each slide to maintain a consistent height on both cabinet sides.
• Start all screws loosely, test the slide motion, then tighten—this gives you wiggle room to correct minor racking.
• Check for parallelism front to back and side to side. A 1–2 mm misalignment can defeat the self-closing catch or cause bounce-back.
• For inset drawer fronts, set your setbacks carefully so the self-close doesn’t pull the front into the face frame too forcefully. A thin felt bumper helps.
• Label your drawers and slides as you go. Keeping pairs together speeds reassembly.

What I liked

• Straightforward install with clear hole patterns and included hardware.
• Smooth, predictable action; self-close keeps drawers from drifting open.
• Stated 50 lb capacity proved realistic for typical household use.
• White finish looks clean and blends well in light interiors.
• Good retrofit option for older furniture and cabinetry using similar slide geometry.
• Limited lifetime warranty offers some peace of mind.

Where it falls short

• Not soft-close and not full extension—set expectations accordingly.
• Bottom-mount roller design can show slight racking on very wide, heavily loaded drawers at full extension.
• The “10 pieces = 5 pairs” packaging language can trip up first-time buyers. Make sure you’re counting pairs for your project.
• Screws are fine, but in composite substrates, upgrading fasteners improves long-term hold.

Use cases that suit it best

• Dressers, nightstands, and general bedroom furniture.
• Utility drawers in laundry rooms or pantries where quiet, reliable closing matters more than full extension.
• Light-to-moderate kitchen drawers that already use bottom-mount roller slides and need a refresh.
• Rental or flip renovations where cost, speed, and reliability are key.

If you’re tackling a shop cabinet, a wide pots-and-pans drawer, or anything over about 50–60 lb loaded, step up to heavy-duty side-mounts. If your priority is a soft, damped close and full access, look at soft-close, full-extension ball-bearing slides instead.

The bottom line

After installing and living with these slides, I’d call them a solid, no-drama replacement for aging bottom-mount hardware. They install easily, run smoothly, and the self-closing feature does exactly what it should—keep drawers shut without fuss. The finish has held up, and the 50 lb rating feels honest in real-world use. Just be clear on the pack size (five pairs, not ten) and on what you’re getting functionally: self-closing 3/4-extension roller slides, not modern soft-close ball-bearings.

Recommendation: I recommend these slides for refurbishing dressers and light-to-moderate household cabinetry where you want a straightforward install, reliable self-closing, and a clean white finish. They’re not the right choice if you need full extension, soft-close, or heavy-duty capacity, but within their lane, they’re a dependable, good-value option.