SD-CityCliq Pole Saw Attachment(12") and Extension Pole(30") fits for Ryobi,Craftsman,Weed Eater,mtd pro,Troy-Bilt,Toro,John Deere,Hus 128LD Most Brush Cutter/String Trimmer

Why I reached for this attachment

Modular yard tools are a real space saver in my shop, so I’m always curious about attachments that promise more capability from a single powerhead. This pole saw attachment with the included 30-inch extension turns a standard trimmer/brush-cutter powerhead into a compact pruning saw. On paper it’s a 12-inch bar with an automatic oiler and a tool-based chain tensioner. In the yard, it ended up being a capable, budget-friendly option with a few setup quirks and some limits you’ll want to know about.

Compatibility and setup

Fit is the make-or-break factor with universal attachments. This one is built for systems that use a 1-inch (25.4 mm) tube and a 5 mm square drive. It mated cleanly with my Ryobi attachment-capable head and also clicked onto a Kobalt head I had handy. An older off-brand powerhead in the shop used a different coupler geometry and wouldn’t lock in—so measure before you buy and confirm your head uses the 5 mm square drive.

Out of the box, the bar and chain weren’t installed. The kit included the basic tools to do the job: a scrench (combo screwdriver/wrench) and hex keys. There weren’t detailed instructions in my box, but if you’ve ever mounted a chainsaw bar, the process is familiar: slip the chain around the sprocket, seat the bar, align the tensioning pin, snug up the cover, and then set the chain tension so it lifts slightly from the bar but snaps back with a gloved finger. Don’t run it without bar oil; I filled the reservoir with standard bar and chain oil before first use and checked the oiling by running the chain for a few seconds—there should be a light mist of oil flinging off the tip.

The 30-inch extension is a separate section with the same coupler system. It adds meaningful reach for higher limbs, but it also changes balance and increases leverage forces on the couplers. Make sure both locking collars are fully engaged and bolts are snug before you start cutting overhead.

Build and design notes

The head uses a 12-inch bar and a low-profile chain (3/8" LP, .050" gauge, 44 drive links). That’s a very common spec, so replacement chains and bars are easy to source. The automatic oiler on my unit worked reliably; oil usage was in line with typical small pole saws, and the bar stayed wet during long cuts. The chain tensioner is “tool-based,” meaning you use the included scrench to turn a small screw; it’s not a toolless adjuster, but it holds tension well once set.

Shaft sections are steel and feel more robust than the price would suggest. There is still some flex when you’re fully extended and reaching, which is normal for modular systems. The couplers are decent—no excessive slop—but you’ll feel a hint of play compared to a one-piece dedicated pole saw. The chain cover and deflector are basic but functional. I’d call the overall construction homeowner grade: not flimsy, not pro-tough.

Cutting performance

The manufacturer claims up to 8-inch diameter cuts. I spent a weekend cleaning up storm-damaged oak and maple limbs and found that to be realistic. On my gas powerhead, 4- to 6-inch branches were fast and drama-free. At 7 to 8 inches, the cut time lengthens and you need to let the chain do the work—no forcing. I also worked around the base of a small ornamental tree and sectioned a roughly 10- to 12-inch trunk by cutting from multiple sides; it’s slow going with a pole saw, but doable if you’re patient and keep the chain sharp.

On a 40V battery powerhead, results depended on the battery and how aggressively I fed the cut. Freshly charged high-capacity packs handled 4- to 5-inch limbs fine. With partially depleted packs or lighter-duty heads, I could bog the chain if I leaned on it. If your powerhead is on the lower end of the torque spectrum, expect to take your time and avoid binding the bar. For heavy pruning days or thicker limbs, a gas head (or a higher-torque cordless unit) makes a noticeable difference.

One caveat: the stock chain on my unit arrived on the conservative side of sharp. It cut, but it felt more like a “safety grind” than a hungry chain. A few strokes with a 5/32" file woke it up, and swapping to a name-brand 90-series 44DL chain later made a clear improvement in cut speed. That’s common on value attachments—budget chains just don’t bite as well.

Ergonomics and balance

With the extension installed, reach is excellent for a homeowner tool, and I could prune from the ground up to the second story on most shrubs and small trees. The tradeoff is leverage: all the weight is out at the end, so every small movement translates into a bigger effort at your shoulders. I recommend using a shoulder strap on your powerhead if it supports one. It helps a lot during longer sessions.

Vibration was reasonable. You’ll feel the engine or motor through the shafts, but nothing unusual for this class. The narrow-kerf chain tracks smoothly on the bar, and with the tension set correctly, I didn’t experience derailments. Plan on checking tension every tank/battery early on—new chains stretch—and then at the midpoint of your workday as a habit.

Reliability and maintenance

So far, the head has held up after multiple pruning sessions: no oil leaks, no stripped fasteners, and no coupler slip. I did re-tighten the bar nuts a couple of times after heat cycles (normal) and checked the coupler set screws before each use. The sprocket and tip show expected wear, and the bar rails are still straight with proper oiling.

A few quick maintenance tips based on my use:
- Fill bar oil every time you refuel or swap batteries.
- Keep the chain properly tensioned; loose chains accelerate wear and derail more easily.
- Touch up the cutters frequently. A sharp chain reduces kickback, load on the motor, and fatigue.
- Wipe the bar groove and oil port when you change chains to keep the oiler flowing.

Safety considerations

It’s easy to overreach with pole saws. Keep your feet planted, cut at chest height or below when possible, and work with the bar slightly to one side of your body. Let the chain stop before walking to your next cut. Because the 30-inch extension increases flex and the chance of pinch, I cut with a lighter touch when fully extended and planned relief cuts to prevent the kerf from closing on the bar.

Kickback risk is real with any pole saw. Avoid burying the upper quadrant of the bar tip. If a branch wants to bind, back out and re-cut from the opposite side.

What I liked

• Broad compatibility with common 1-inch, 5 mm square-drive systems; it snapped right onto my Ryobi and Kobalt heads.
• Automatic oiler that actually keeps up during longer cuts.
• Common bar/chain spec makes upgrades and replacements easy.
• The 30-inch extension adds meaningful reach without turning the setup into a wobble monster.
• Solid homeowner-grade build for the price.

What could be better

• Mine arrived without detailed instructions. Assembly is straightforward if you’ve used chainsaws, but first-timers may want a quick start guide.
• The stock chain was serviceable but not impressive. Budget for a better chain if you cut frequently.
• Lower-torque battery heads can bog in thicker limbs, so match the attachment to a capable power source.
• There’s minor play in the couplers compared to a one-piece pole saw, which is expected but worth noting.

Who it’s for

This attachment makes the most sense for homeowners who already own an attachment-capable powerhead and want to prune small to medium limbs a few times a year. If you’re comfortable tensioning a chain, adding bar oil, and keeping cutters sharp, it’s an easy upgrade. Landscapers or anyone pruning daily will still be better served by a dedicated pro pole saw with a rigid shaft and tool-free adjustments.

Recommendation

I recommend this pole saw attachment with some practical caveats. It fits common systems, cuts up to its advertised capacity when paired with a capable powerhead, and the oiler and tensioner do their jobs. You’ll need to handle basic chainsaw setup and maintenance, and I’d plan on upgrading the chain. If you expect a plug-and-play tool or you’re running a low-power battery head, look elsewhere. But as a value-minded way to add pruning capability to an existing modular setup, it’s a useful, dependable addition to the kit.