DeWalt Leather Electrician Pouch

First impressions and setup

I brought this leather pouch onto a residential remodel to see if it could replace my mixed bag of nylon pouches for electrical work. Out of the packaging, it felt substantial without being a brick: about 1.28 lb empty, with a compact footprint that doesn’t flare out too far from the hip. The nubuck top‑grain leather is supple right away—no stiff break‑in period—and the double stitching and rivets at stress points look purposeful rather than decorative. The brown dye is even, and the overall silhouette keeps a low profile.

There’s no belt included, so I threaded it onto my standard 2-inch work belt. The tunnel accommodates a thicker belt without a fight, and once cinched it rides level. I also liked that the top has a rigid carry handle; grabbing the pouch to move from the truck to the panel is quicker and cleaner than palming a loaded main pocket.

Materials and build quality

The leather is nubuck top‑grain, which is a sweet spot for electrician pouches: tough enough to resist tearing and abrasion, yet soft enough not to chafe your side. The secondary pocket material is polyester, which is a smart choice for interior sleeves where slicker surfaces help with in-and-out motion for screwdrivers and pencils.

Stress points are riveted and double stitched, which matters once you start stuffing lineman’s pliers, nut drivers, and a few boxes of wire nuts. The hammer loops are leather rather than metal, so they don’t rattle or scar up your hammer handle, and they feel stout. Overall, the build inspires confidence—even the edge finishing is tidy, with minimal fraying on fabric sections.

Dimensions are practical: roughly 11-3/4 inches tall, 9-3/8 inches long, and about 2-1/4 inches deep. DeWalt rates it for a total storage capacity around 102 cubic inches and up to 15 lb of load. That tracks with my on‑site use—it’s sized for essential electrical tools rather than “everything I own.”

Organization and pocket layout

The layout is cleaner than many electrician pouches. You get eight pockets of varying sizes and a series of sleeves for slim tools and pencils. The main dump pocket is roomy enough for wirenuts, pigtails, a small tester, and a handful of wirenut bags or butt splices. The secondary pocket fits a compact meter or a small box of staples. Tool sleeves along the rim are sized appropriately for:

• Two to three screwdrivers or a multi‑bit driver
• Needle‑nose and lineman’s pliers
• Wire strippers and flush cutters
• A pencil and Sharpie

The two leather hammer loops sit on opposite sides. I use one for a standard claw hammer or a small milled face hammer when framing or mounting boxes; the other often holds a rubber mallet or a longer tool like a level or torpedo square. They’re not oversized, so heavier framing hammers still fit but sit snug.

There’s also a chain on the face. Functionally, it works well for electrical tape rolls; you can also clip a lanyard or tether a tape measure if you prefer that method. There isn’t a dedicated molded tape measure holster, so if you like a fixed tape pocket, you’ll be using the belt clip on your tape or relying on the chain.

Carry comfort and ergonomics

Loaded with my typical service setup—lineman’s, needle‑nose, strippers, stubby driver, multi‑bit driver, non‑contact tester, small multimeter, assorted wirenuts and tape—the pouch stays upright without drooping. Weight distribution is centered and the bottom is structured enough that tools don’t migrate to a lopsided clump. The low‑profile depth helps when squeezing between studs and avoiding snags on ladder rails.

The carry handle is more useful than it sounds. On service calls, I left the pouch off the belt and just carried it by the handle room to room, then hooked it on a rung or set it on a surface. It’s also handy for quick belt swaps without shedding your load onto the floor.

Leather’s comfort advantage is real: it molds a bit to your hip after a day, and the nubuck surface doesn’t cut into clothing. The trade‑off is weight. This pouch isn’t heavy, but it’s not ultralight nylon either. If you count ounces above all, you’ll notice the leather. If you prioritize stability, it feels right at home.

Capacity and on‑the‑job performance

For rough‑in days, I favor a larger rig, but for finish work, troubleshooting, or light fixture swaps, this pouch hits the sweet spot. The 102 cubic inches are deceptive because the structure keeps everything tidy and upright. I rarely had to dig; sleeves hold drivers and pliers at predictable heights. A compact meter fits without bulging.

The hammer loops ended up being versatile. On a light commercial job I used one for a drywall hatchet while patching, and the other to tuck a conduit reamer. Neither flopped around, and the leather loops are kinder to tool finishes than metal rings.

I wouldn’t exceed the 15 lb rating. With pliers, drivers, meter, fasteners, and tape, I was hovering around 7–9 lb. It’s comfortable there. Push past that and any single pouch starts to tug.

Durability and weather considerations

After a damp morning in a crawlspace, I noticed a couple of orange specks on the metal chain. A quick wipe and a drop of oil solved it, but it’s a reminder: leather plus metal hardware prefers to stay dry. The leather itself handled moisture fine once I let it air dry and applied a light conditioner later. I’d recommend periodic leather care—a thin coat of conditioner or wax—and drying the pouch if it gets wet. If you routinely work in wet conditions, nylon may be the safer choice.

Stitching has held up cleanly, even where I wedge in a bulky multi‑bit driver. Rivets are set flush with no sharp edges inside pockets, so you don’t shave insulation off wire by accident. The polyester liners show minimal scuffing after weeks of use, and they make it easier to brush out debris.

What could be improved

• A dedicated tape measure holster would be nice. The chain is versatile, but tape measure management ends up on your belt clip.
• The empty weight is reasonable for leather, yet heavier than comparable nylon pouches. If you chase ultralight, this isn’t it.
• The metal chain will spot‑rust if you don’t dry it after getting soaked. A stainless chain or coated hardware would be a welcome upgrade.
• It doesn’t ship with a belt. Not a problem for most pros, but a bundled option would help new setups.

Value and warranty

With a limited lifetime warranty covering manufacturing defects (not wear and tear), the pouch sits in a comfort zone for long‑term use. The materials and stitching justify the investment. You’re paying for a leather build that should age well if you take basic care of it. I appreciate that the pouch is made in India; the workmanship on my sample is consistent, with straight stitching and clean cuts.

Who it’s for

• Electricians and maintenance techs who want a compact, organized pouch for service work and installs
• DIYers who prefer leather’s stability and feel over floppy nylon
• Anyone who values a carry handle for quick grab‑and‑go and ladder moves

Who should look elsewhere: If you need to carry a full day’s worth of fasteners, hand tools, and a cordless driver in one pouch, this isn’t the pack mule. And if your work is routinely wet or muddy, a synthetic pouch might be lower maintenance.

Recommendation

I recommend this leather pouch for electricians and techs who prioritize tidy organization, stable carry, and durable materials in a compact form. The pocket layout is well thought out, the leather and stitching are robust, and the top handle adds real convenience on the job. As long as you’re comfortable with the modest extra weight of leather and you don’t need a dedicated tape measure holster, it’s a dependable, comfortable pouch that keeps the essentials right where you expect them. Keep it dry, give the hardware a quick wipe after wet days, and it should serve you for years.