DeWalt Flexible High-Durability Grip Work Gloves

First impressions

I put the DeWalt grip gloves straight to work on a mixed week of tasks: framing and exterior trim in damp weather, an oil change in the garage, and a day moving pavers and wet lumber. Right away, the double-dipped grip coating stood out. Where most lightweight knit gloves get slick the moment they meet water or oil, these maintained a surprisingly confident hold on smooth metal, wet PVC, and sealed lumber. They feel like a practical middle ground—more protective and grippy than basic single-dip utility gloves, but still flexible enough for all-day wear.

Build and design

These are a 13-gauge, seamless-knit nylon glove with a double-dipped grip coating over the palm and fingers. The build hits a sweet spot:

• 13-gauge knit shell: Thin enough for good dexterity yet substantial enough to outlast the bargain-bin stuff.
• Double-dipped coating: The outer layer is abrasion-resistant, while the inner layer helps seal out moisture and oil on the working surfaces of the glove.
• Water- and oil-resistant palm: It’s not a waterproof glove, but the coated areas do a good job shedding liquids so you can keep your grip.

Color is gray/black, sizes run from S to 2XL, and the glove is covered by a 1-year limited warranty. The back-of-hand remains uncoated for breathability, while the palm and fingers are fully coated for traction and durability.

Fit, comfort, and dexterity

I wore my usual size and the fit was spot-on: snug without hot spots. The glove molds to the hand after a few minutes, and the seamless knit prevents seams from rubbing under pressure points like the thumb crotch. A few notes from use:

• Comfort: The back-of-hand breathes well. In warm weather, the coated palm still traps some heat—as expected with any dipped glove—but these are comfortable for full-day projects.
• Dexterity: I could thread small nuts, start finish screws, and handle electrical connectors without feeling clumsy. They’re not surgical, but for a 13-gauge glove with a thickened palm, dexterity is very good.
• Cuff: The cuff stays put and keeps debris out. It’s a snug, simple design that doesn’t snag.

One limitation: these are not touchscreen-friendly. Plan on taking one glove off when you need to use a phone or a tablet.

Grip performance in real conditions

The double-dipped coating earns its keep in messy environments.

• Wet work: On rainy framing days, I kept a firm hold on wet 2x material and metal hardware. The coating prevents water from forming a slippery film between the glove and the surface.
• Oily surfaces: During an oil change, I could handle filters and smooth sockets without the telltale “spin” that happens with foam latex or worn nitrile. The gloves stayed usable even after picking up oil-slick parts; a quick wipe on a rag restored traction.
• Smooth materials: On PVC and painted steel, grip remained secure. On glass or very polished stainless, grip is still better than bare hands but requires more deliberate pressure.

If you fully submerge your hands or work in standing water, remember the back-of-hand knit will absorb moisture. These are water-resistant where they’re coated, not waterproof overall.

Protection and limitations

Protection is where expectations need to be clear. This is a light, general-purpose glove with a tough coating. It offers:

• Good abrasion resistance in the palm and fingertips.
• A barrier against incidental oil, water, and grime.
• Basic protection from minor scrapes and splinters.

It does not offer:

• Cut protection with a formal rating. If you’re handling sheet metal, wire rope, or sharp edges, switch to a cut-rated glove.
• Impact protection. There are no reinforced knuckles or back-of-hand padding.
• Thermal insulation or wind resistance. Not a winter glove, and not intended for hot surfaces or sparks.

In short, it protects your hands for daily tasks and keeps your grip when things get messy, but it’s not a specialty glove for high hazards.

Durability

After multiple project days, the coated areas show light polishing at the fingertips but no cracking or delamination. The second dip clearly extends the service life compared to single-dipped utility gloves I’ve used; they’re less prone to wearing through at the thumb and index finger. The knit shell hasn’t frayed, and the elastic has stayed tight. As with any dipped glove, punctures from screws, nails, or sharp edges are still possible, so don’t treat them like puncture-proof PPE.

A good habit is to rotate pairs if you’re working daily—the coating benefits from time to dry fully between uses.

Care and maintenance

• Rinse off grit and mud at the end of the day.
• Hand-wash or machine-wash cold with mild detergent.
• Air-dry only; avoid high heat, which can shorten the life of the coating.
• Store out of direct sunlight to prevent premature aging of the polymer.

This quick routine keeps the coating grippy and the knit fresh.

Sizing advice

The size range from Small to XXL covers most hands. The 13-gauge knit fits close; if you’re between sizes or prefer a looser feel, consider sizing up. For heavy rotation, I’d buy two pairs in your primary size so you can alternate while one dries.

Use cases where they shine

• General carpentry and jobsite tasks: Carrying lumber, driving screws, handling fasteners, setting anchors.
• Material handling: Pavers, bricks, pallets, and wet boxes.
• Light mechanical work: Oil changes, belt replacements, hose clamps, and under-hood tasks where oil and coolant can compromise grip.
• Facilities and manufacturing: Moving parts and fixtures where a consistent hold matters more than heavy protection.
• Yard and home projects: Pressure washing, deck cleaning, and hauling debris.

Where they fall short

• Not for cold weather or wind: No insulation and not wind-resistant.
• Not cut-rated or impact-rated: Don’t substitute these for specialized PPE.
• Not fully waterproof: The back-of-hand knit will absorb water in sustained exposure.
• No touchscreen capability.

These are trade-offs inherent to the glove’s category and price point, but they’re worth calling out.

Value and warranty

For a double-dipped glove with this level of grip and durability, the value is strong. Many budget options feel great on day one and slick by week two; these hold their traction better under wet and oily conditions. Add the 1-year limited warranty, and you’ve got a solid, low-risk pick for daily use.

Pros and cons

Pros
- Confident grip in wet and oily conditions
- Durable double-dipped palm and fingers
- Comfortable, breathable 13-gauge knit
- Good dexterity for fasteners and small parts
- Wide size range (S–2XL)

Cons
- Not cut-rated or impact-protective
- Not waterproof on the back of the hand
- No touchscreen compatibility
- Not windproof or insulated

Recommendation

I recommend the DeWalt grip gloves for anyone who needs reliable traction and solid durability in a lightweight, everyday glove—carpenters, mechanics, facilities teams, warehouse workers, and DIYers alike. They excel where many knit gloves fail: keeping a trustworthy hold on wet and oily surfaces without feeling bulky. Just match them to the right tasks. If you’re dealing with sharp edges, heavy impacts, or cold weather, choose a cut-rated, impact-rated, or insulated glove instead. For general utility, construction, manufacturing, and material handling, these strike a smart balance of grip, comfort, and longevity.