ECUDIS 1/8-IP Lighting Loops with Link Buckle Connectors for Light Fixture Chandelier Chain Extension, Pack of 2

Why I reached for these loops

I had a vintage pendant that needed to be converted from stem mount to a chain-hung setup, and I wanted hardware that would look period-appropriate without adding a lot of bulk. The ECUDIS lighting loops checked the right boxes on paper: 1/8-IP threading (the standard for most lamp parts), an antique brass finish, a stated 50 lb load rating, and the promise that the cord could pass through the loop—handy for a clean run without awkward bends.

What arrived was a tidy little kit: two iron loops in antique brass, two 1/8-IP threaded nipples (standard 3/8-27 lamp thread), two 1-inch thread inserts, and two small 4 mm “link buckle” connectors (quick links) for joining a chain. For a small repair or a straightforward fixture conversion, this is very close to a one-box solution.

Build and finish

The loops are iron with a coated finish. In hand, they feel solid and surprisingly stout for their size. The antique brass finish isn’t overly glossy; it leans toward a muted, warm tone that blends well with most antique-brass chains and canopies. It’s not a perfect match for every “antique brass” on the market—finishes vary widely—but it didn’t stand out as off-color in my install. The coating looks uniform with no thin spots or burrs at the eyelet, and the inner radius of the loop is smooth enough that it doesn’t chafe the cord sleeve.

The 4 mm quick links are functional and cleanly plated. They’re on the smaller side, which is fine for light-duty decorative chain or 3–4 mm links. If you’re pairing with a heavier chain, you may want upsized quick links for easier threading and better load margins.

Threading and compatibility

These are correctly cut for 1/8-IP (3/8-27) threads—the ubiquitous lamp standard. If you’re expecting 1/8-inch NPT pipe threads, this won’t fit; electrical lamp parts use a different thread form and pitch. A quick way to double-check your existing hardware: 1/8-IP measures about 3/8 inch outside diameter with 27 threads per inch. If your caliper says roughly 0.405 inch OD and your old pieces spin nicely into a typical lamp nipple or crossbar, you’re in the right system.

The included nipples are standard 1/8-IP and about 1 inch long, which is the most useful size for getting through a canopy and into a crossbar or coupling. In my case, the length was just right to clear the canopy while leaving enough thread engagement on both ends.

Installation experience

Swapping the existing stem for these loops took all of ten minutes:

• I removed the old stem and canopy.
• Fed the cord through the ECUDIS loop and then through the threaded nipple.
• Threaded the nipple into the fixture’s coupling, then cinched the loop on top.
• Rehung the canopy, attached the chain with the included quick link, and dressed the cord through the chain.

The cord pass-through is a small but welcome detail. Some loops force a tight bend at the exit, which can kink the insulation. These let the cord run cleanly with a gentle radius. Do note that there’s no built-in strain relief. If the cord will carry any significant weight or be subject to movement, add a strain-relief bushing or tie a UL knot above the loop so the chain bears the load—not the conductors.

Everything threaded together smoothly—no cross-threading or gritty feel. Once snugged down, the loop didn’t wobble. I did add a thin star washer under the canopy for bite, plus a 3/8-27 jam nut (not included) to lock the nipple’s position. A jam nut or two is an inexpensive addition I’d recommend for a rock-solid setup and to prevent gradual loosening from vibrations.

Load rating and safety

The loops are rated for up to 50 lb, which puts them in the sweet spot for most medium chandeliers, bowl pendants, and decorative fixtures. I hung a 26 lb chandelier with 8 feet of chain (about 2 lb) without any drama—no flex, no creaks, no finish cracking around the eye. Still, load rating is only one piece of the safety picture:

• Ensure the ceiling box, crossbar, screws, chain, quick links, and any couplers are also rated for the full load.
• Always let the chain carry the weight; the cord is not a support.
• If installing in a damp environment, remember these are iron with a coated finish—resistant to corrosion, but not stainless. Covered porches are fine; direct coastal exposure is not ideal.

Where these loops shine

• Converting a fixed-stem pendant to chain-hung: The pass-through loop keeps the profile clean and avoids an awkward wiring route.
• Repairing a broken or underbuilt loop: If you inherited a fixture with a pot-metal loop that stripped out, these iron loops are a clear upgrade.
• Matching traditional hardware: The antique brass finish blends well with classic and transitional fixtures without calling attention to itself.
• Light hanging beyond lighting: They’re perfectly serviceable for hanging small planters or fruit baskets within the 50 lb limit, provided the rest of your hardware is up to the task.

What could be better

• Hardware completeness: I would have liked a pair of jam nuts and maybe a couple of finish washers in the bag. The essentials are here, but those small extras make a professional install easier.
• Quick link size: The included 4 mm connectors are fine for light chain. If you’re using heavier chain, you’ll likely want larger quick links for a better match in scale and feel.
• Finish options: Antique brass is a good baseline, but having a brushed nickel or black option would cover more modern fixtures without a trip to the parts aisle.

None of these are deal-breakers; they’re just areas where the kit could move from “very good” to “near perfect” with minimal additions.

Tips for a smooth install

• Verify thread standard: Look for 3/8-27 markings or measure with a caliper. If your old part is 1/8 NPT (tapered pipe), it will not be compatible.
• Plan your stack-up: Measure your canopy thickness, crossbar depth, and how much thread you’ll need on both sides of the nipple. If you need more reach, pick up a longer 1/8-IP nipple and a couple of jam nuts.
• Add strain relief: Use a strain relief bushing or a UL knot above the loop so the chain, not the cord, bears the weight.
• Lock it down: A jam nut and a star washer go a long way toward keeping the loop aligned and tight over time.
• Match your chain: If your chain is thicker than 4 mm or has a different finish tone, swap the quick link for one that matches both in size and color.

Durability so far

After several weeks with a moderately heavy chandelier, the loops have held position with no signs of finish wear or loosening. The iron feels confidence-inspiring, and the coated finish has shrugged off fingerprints and the occasional dusting without spotting. I wouldn’t hesitate to use them again indoors or in a covered outdoor area where dripping moisture isn’t a concern.

Final thoughts and recommendation

The ECUDIS lighting loops are a simple, well-executed solution for chain-hanging a fixture or refreshing tired hardware. The threading is correct and clean, the finish is balanced and consistent, and the cord pass-through design makes for a tidy install. The kit is nearly complete; adding your own jam nuts or washers is inexpensive and, in my view, worth doing.

I recommend these loops. They hit the right blend of compatibility, build quality, and ease of installation for most lighting projects in the 50 lb-and-under range. If you verify your thread standard, plan your hardware stack, and mind basic strain relief, you’ll get a secure, clean-looking result with minimal fuss.