StealthMounts Bench Belt - Universal Tool Holder | Tool Holster Set - 6 Pack | Perfect Tool Hanger Storage Dock for Power Tools, Tape Measures and Belt Clips

Why I tried these mounts

I’m constantly misplacing small, clip-on tools—tape measures, a flashlight, even my impact driver when I’m bouncing between the bench and the ladder. I installed a 6-pack of StealthMounts Bench Belt mounts in a few spots around my shop and on a jobsite ladder to see whether a simple, universal clip dock could tame the daily shuffle. Short answer: they helped more than I expected, with a few quirks worth knowing before you buy.

Build quality and design

Each mount is a low-profile ABS injection-molded block with a narrow “bench belt” slot (listed at 1.26 in x 0.275 in). The plastic feels dense and rigid, with clean edges and a smooth finish that won’t chew up metal belt clips. The rigidity is great for holding shape and resisting wear, but like most hard plastics it doesn’t love excessive point pressure from fasteners—more on installation below.

The form factor is compact enough to line up several in a row without crowding. I mounted three on the side of a rolling cabinet for drills and drivers, one by the shop door for a flashlight, and two on a pegboard panel for tape measures and a trim square with a clip. The blue color is easy to spot without being loud, and the parts look consistent and well-made.

Installation notes

They mount with two screws each. There’s no hardware in the box, so plan accordingly. Here’s what worked best for me:

• Use #6 or #8 pan-head screws. Pan or truss heads spread load better and seat nicely in the pockets. #8s will fit but are snug; #6s were perfect into plywood and MDF.
• Pre-drill, especially in hardwood, to avoid stressing the plastic as you pull the mount tight.
• Do not overtighten. Snug is enough. ABS can crack if you torque the screws as if you’re hanging cabinets.
• On pegboard, I backed the mounts with a scrap of 1/2 in plywood so the screws had more to bite into than thin fiberboard.
• Spacing matters. For tape measures and drivers, 4–5 inches center-to-center kept clips from colliding when docking in a hurry.

I also tried a temporary setup on an aluminum ladder using short machine screws and nylon locknuts through an accessory tray. It worked well, but be mindful of your ladder’s structure—don’t compromise safety for convenience. Where I couldn’t use hardware, a strip of VHB tape held a mount surprisingly well on a steel cabinet, though I still prefer screws.

Day-to-day use

The slot geometry is the star here. Most tape measure clips, drill/driver belt clips, and flashlight pocket clips seat with a firm, predictable click. There’s a bit of side-to-side stability built in, so the tool doesn’t wobble or rattle when you bump the bench.

• Tape measures: Standard 25–35 ft models docked cleanly. I had one with an extra-thick clip that felt tight on the first few cycles; after a dozen uses it smoothed out, but it’s still a snug fit.
• Drills/drivers: My 18V impact driver with a factory belt clip hung securely. I tried deliberately yanking it off at an angle—still no accidental release. Retrieval is one-handed and fast.
• Flashlights and pens: Anything with a decent pocket clip works, and putting one near the exit door has already saved me a late-night scramble more than once.
• Safety glasses: If yours don’t have a clip, add a small carabiner to the mount’s screw hole or nearby hardware; otherwise they’re not the best candidate.

I intentionally installed one mount inside a tool cabinet door to see if motion would shake things loose. With normal opening and closing (and rolling the cabinet around), nothing budged. In a vehicle or trailer, I’d still be cautious about very heavy items on rough roads, but for tape measures and hand-size drivers it’s solid.

Compatibility caveats

The listed slot height of 0.275 in is a good middle ground, but not all clips are created equal. A few observations:

• Thick or rubber-coated clips may feel tight. You can ease the first contact by slightly chamfering the clip’s leading edge with a file or sandpaper, or by wearing in the mount with repeated insertions.
• Clips with aggressive hooks can scrape. The plastic holds up, but I smoothed a burr on one metal clip to keep the motion clean.
• Curved clips work, but the most confident hold came from flatter, springy stainless clips like those on many pro tape measures and OEM drill brackets.

If your kit is heavy on tools without clips, these mounts don’t change that reality. They’re excellent at what they’re designed for; they’re not a universal catch-all.

Durability and wear

After several weeks of daily docking and undocking, I’m not seeing deformation or gouging. ABS was the right choice: rigid enough to resist slot “spreading,” and slick enough to keep friction low. The only time I worried about durability was during the first install when I test-cranked a screw too tight and heard the unmistakable creak of plastic under stress. Backed off, no harm done, but it’s a reminder to snug, not crush.

In terms of load, they’re better than they look. A tape measure is trivial; an 18V impact driver with a battery is fine too. I wouldn’t hang a framing nailer or sledge from one clip—if you’re trying to do that, you’re asking the wrong accessory to solve the problem.

Placement ideas that worked

• Bench side and cart uprights: Keep drivers and tapes exactly where you reach most.
• Inside cabinet doors: Reclaim vertical space; just make sure the door and shelves clear.
• Ladder accessory tray or side rail (where safe): Great for a drill, pencil, and chalk line when you’re up two rungs and need hands-free transitions.
• Van or trailer panels: For clips that won’t snag during transit; position slightly inward to avoid brushing against cargo.

A small tip: mount one at the entryway at chest height for your most-used flashlight. It’s become habit to dock it as I walk in and grab it on the way out.

What could be better

• Include screws. Even a small pack of #6 pan-heads would make first-time setup more frictionless.
• Clearer guidance on max clip thickness. A simple diagram would save guesswork for unusual clips.
• Color options. Blue is fine; a neutral or black version would blend into more shop environments.

Price-wise, they’re not bargain-bin plastic. Given the molding quality and how much tidier my workflow feels, the value is there, but expect to pay a premium compared to DIY or 3D-printed solutions. In my experience, these feel smoother and more durable than the printed mounts I’ve tried.

The bottom line

This is a thoughtfully executed, universal dock for anything with a belt or pocket clip. It turns dead space on cabinets, carts, and ladders into useful parking spots, and it does so without drama: tools go in and out one-handed, they don’t rattle, and they’re where you expect them to be. Installation is straightforward as long as you mind your hardware and don’t overtighten.

I recommend these mounts if your everyday tools—tape measures, impact drivers, flashlights—already live on clips and you want a simple, repeatable way to store them where you work. They’re durable, compact, and versatile across shop, jobsite, and vehicle. If most of your tools lack clips or you need storage for heavy, awkward shapes, look elsewhere. For clip-on essentials, these are an easy win that actually sticks.