Jejavu 1" Specialty Wrought Iron Patio Furniture Feet Glides, Plastic Chair Leg Caps for Specialty Chairs, Floor Protectors, Pack of 16, Black

Why I tried these

I’ve been slowly rescuing an aging set of wrought-iron patio chairs that had seen too many seasons: missing feet, rust rings on the concrete, and that unmistakable screech every time someone pulled a chair back. Enter the Jejavu 1-inch wrought-iron chair glides. I wanted a tidy, low-profile cap that would actually stay put, quiet the noise, and protect both the chair and the surface under it. After installing them across a small outdoor set (and a couple of metal stools indoors), here’s how they fared.

What they are—and who they’re for

These are hard plastic caps designed to press into a very specific kind of wrought-iron leg: a cup-shaped foot with a 1-inch inside diameter that curves inward at the bottom, like the underside of a flying disc. If your furniture has straight tubular legs, flat metal pads, or a different cup shape, these aren’t the right match. But if your feet have that concave cup profile, this design hits the target.

They arrive in a pack of 16, finished in black (there’s also a white option). The quantity is tuned for a small patio set—four chairs plus a couple of spares—which is convenient if you’re doing a full refresh rather than replacing one or two feet.

Checking fit before you install

Fit is everything with these. Jejavu’s “1-inch” refers to the inside diameter of the metal cup, not the outside of the leg. I measured with calipers, but a snug tape measure can work if you’re careful. Just as important as the measurement is the shape: the metal cup needs that inward-curving, concave bottom. If the profile on your furniture is different, you may get a partial fit at best, and you’ll likely need a dab of silicone adhesive to keep a cap seated—or you should look for a different style entirely.

One practical tip: dry-fit a single cap before prepping every chair. It’s the fastest way to confirm you’ve got the right size and shape.

Installation experience

The plastic here is intentionally rigid, and that stiffness is a double-edged sword. The upside: once they’re in, they hold. The downside: they don’t push in by hand. Expect to use a mallet.

My prep routine:
- Flip the chair upside down and support the frame on something that won’t mar the finish (a folded towel or a bag of mulch works).
- Remove any remnants of old caps and scrape off rust and debris inside the cup. A small wire brush or folded sandpaper helps.
- If bare metal is exposed, a quick pass with rust-inhibiting paint gives you a clean, sealed surface before installing the new caps.

For installation, I aligned the cap squarely with the cup and used a rubber mallet with light, even taps around the perimeter, then a couple of firmer hits to fully seat it. On a couple of legs that were slightly deformed from rust, I had to true the cup with pliers first. If a cap felt stubbornly tight, warming it briefly in hot tap water made the plastic just pliable enough to help it start. Conversely, if a cap seated too easily on one leg, a thin bead of clear silicone inside the cup locked it in place without being permanent.

A word of caution: swinging a metal hammer directly at the cap is a good way to slip and pinch a finger. A rubber mallet or a hammer with a scrap of wood as a buffer is safer and gives more control.

Performance on different surfaces

I tested the caps on concrete, composite decking, and hardwood. On the patio, they eliminated that gritty scrape and stopped the rust rings that were forming under the old, cracked feet. On the deck, they didn’t gouge or leave tracks. Indoors, they slid smoothly on finished hardwood without leaving marks, and the noise drop was immediate—no squeal, just a soft glide. The hard plastic composition isn’t cushioned like felt, but it’s much more durable outdoors and still gentle on most smooth surfaces.

One small note: these are glides, not anti-slip pads. If your priority is grip on slick tile, you’ll want a different style. For most patio and indoor use, the balance between protection and glide felt right.

Durability and hold

After installation, none of the caps worked themselves loose. The stiffness that makes installation a chore also means they stay put once seated properly. Over several weeks of daily use and a couple of rainstorms, I saw no cracking or edge fraying. The black finish blends into most dark metal frames and looks original from a standing distance.

UV and weather exposure always take their toll on plastics, but these feel thick and dense enough to outlast the softer, cheaper replacements I’ve used in the past. I’ll update my notes after a season or two, but early signs are promising.

Design choices that matter

• Shape-specific fit: The concave-cup requirement is a feature, not a flaw. Designing for a specific foot style allows a snug, mechanical fit without relying on adhesives.
• Rigid plastic: Great for retention and wear; challenging for install. I prefer this trade-off for outdoor furniture because softer plastics can deform quickly under weight and grit.
• Color options: Black and white covers most frames. Black hides scuffs best outdoors.
• Pack size: Sixteen is practical for full sets, but overkill if you’re replacing one or two. I’m happy to have spares; your mileage may vary.

Where the experience can go wrong

• Slightly off measurements: A 7/8-inch cup or a cup deformed by rust will fight you. If you find yourself force-hammering to the point of rebound, stop and reassess fit or clean-up.
• Wrong leg style: If your leg bottom isn’t concave, compatibility is questionable. Adhesive can help with marginal fits, but it won’t fix a fundamental mismatch.
• Installation impatience: These aren’t press-fit by thumb. Set up a safe work surface, use a mallet, and take your time. The five-minute installation per chair is worth the secure hold.

Maintenance and small optimizations

• Rotate chairs occasionally to even out wear on high-traffic corners.
• If you live near the coast or see a lot of freeze-thaw cycles, a quick seasonal inspection helps you catch early issues with rust or cap loosening.
• Keep a couple of spare caps from the pack in a drawer. If one walks off during a move or a cleaning, you won’t be stuck hunting for a match later.

Value

Assuming they fit your furniture, the value proposition is strong. A full set refresh stops rust stains, protects decking, and makes daily use quieter and smoother. The rigid plastic and secure seating reduce the chance of caps popping out mid-season—a common headache with generic, softer plugs. If you only need two replacements, the pack size may feel like overbuying, but the per-foot cost still compares favorably to piecemeal options, and the convenience of immediate spares matters more than you think.

The bottom line

The Jejavu chair leg caps succeed by focusing on a specific furniture footprint and executing the basics—fit, hold, glide, and durability—without frills. The installation requires a bit of patience and a mallet, but the payoff is immediate once they’re seated: quieter chairs, protected surfaces, and a cleaner, finished look that blends well with wrought iron.

Recommendation: I recommend these for anyone with wrought-iron furniture that has 1-inch, inward-curving cup feet. They’re sturdy, they stay put, and they improve both the user experience and the condition of your floors and deck. I wouldn’t recommend them if your furniture uses straight tubular legs or a different foot geometry; in that case, look for a style matched to your leg profile rather than forcing a fit. Measure carefully, prep the cups, and use the right installation approach, and you’ll likely be as satisfied with the result as I am.