HANWER 200 PCS Glue Points for Balloons, Removable Sticky Point Tape, Adhesive Double Sided Clear dots for Craft Decoration

Why I reached for these glue dots

Planning a small celebration at home, I wanted a way to get balloons and lightweight decorations up without hauling a helium tank or peppering my walls with tape and thumbtacks. I tested HANWER’s clear glue dots as a low‑profile, removable option. Over a few weeks, I used them for a birthday balloon ceiling, to hold a tabletop number display in place, and even to hang a run of holiday cards on a painted door. They’re simple, inexpensive, and—within their limits—surprisingly effective.

What you get

• Two compact rolls with 100 dots each (200 total)
• Clear, double‑sided adhesive dots measuring roughly 12 mm across
• Each dot sits on a release liner; you apply one side, peel the film, and set your item

There’s nothing complicated here, and that’s the appeal. The dots are low‑visibility once applied, so they don’t compete with your decor.

Setup and application

The dots work best if you avoid handling the sticky surface with your fingers. Here’s the routine that gave me the most reliable results:

1. Clean the surface lightly (a dry microfiber cloth to remove dust; on glass or metal, a bit of isopropyl alcohol).
2. Press a dot—still on the roll—onto the surface you want to stick to (ceiling, door, glass, etc.).
3. Pull the roll away to leave the dot behind.
4. Peel the protective film from the dot, then press your balloon or decoration into the dot and hold for 5–10 seconds.

An alternate approach is to put the dot on the item first, then place it on the surface. That worked fine for balloons, but I saw better accuracy and fewer fingerprints when I transferred the dot to the surface first.

For heavier or stubborn items (like foil balloons or small cardstock signs), doubling up the dots—two side by side, or one stacked on another—boosted initial tack and staying power.

Adhesion and hold

On clean, painted ceilings (semi‑gloss) and smooth interior doors with gloss paint, the dots held standard 12‑inch latex balloons in place for multiple days. I had a balloon ceiling that stayed intact for three nights, and most balloons were still up on day four. With foil (Mylar) balloons, hold was more variable; the smooth foil surface and additional weight seemed to push the limits of a single dot. Doubling dots made the difference, but I still wouldn’t rely on them for large, helium‑sized foil numbers or letters unless you’re okay checking and pressing them back occasionally.

For tabletop decorations, one dot wasn’t always enough to counter small bumps or airflow from a fan. Two dots under the base of a lightweight “30” sign kept it from wobbling or sliding around.

As for holiday cards, the dots gripped card stock reliably and hung flat against a gloss‑painted door. The hold surpassed typical clear tape, which tends to curl and fail on painted surfaces.

Surface compatibility

• Painted ceilings and doors (semi‑gloss, gloss): Excellent adhesion, reliable removal with no paint lift in my tests.
• Painted walls (eggshell and matte): Mixed results. On a matte wall, some dots lost grip within a day; on eggshell, better but still inconsistent. I’d avoid matte walls for anything you want to stay put for more than a few hours.
• Glass, tile, and metal: Very strong hold; removal was straightforward when I used a slow peel or “roll-off” motion.
• Textured surfaces: Not ideal. The dot can’t bridge small gaps in heavy texture, which leads to early failure.

Humidity and dust are the enemies here. In a steamy bathroom or dusty corner, expect reduced hold time. A quick wipe before application helps a lot.

Removal and residue

On smooth, glossy painted surfaces and glass, removal was clean for me. The best technique was to roll the edge of the dot with a fingertip to gather it and then pull slowly. If a tiny bit of adhesive remained, it rubbed off like a soft gum eraser.

Two cautions:
- Paper and delicate finishes: The dots can be too aggressive for thin paper if you hope to preserve it pristine. A couple of my holiday cards showed light surface tearing where the dot was attached. If you’re saving keepsake cards, stick to the corners or use a less aggressive tape on the paper side.
- Matte paint: I didn’t lift paint, but matte finishes feel more fragile. If you have any doubts, test in a low‑visibility spot first.

Use cases that make sense

• Balloon ceilings without helium: Latex balloons adhered easily; two dots per balloon for longer events or warm rooms improved confidence.
• Flat party backdrops: Lightweight banners and paper fans hung well on semi‑gloss paint and glass.
• Tabletop decor anchoring: Dots under lightweight centerpieces prevent sliding without visible hardware.
• Quick display boards: On glass or metal, you can “pin” paper or thin foam pieces without magnets or clips, as long as you don’t need to preserve the paper.

Where they fall short

• Textured walls and matte paint reduce performance significantly.
• Foil balloons can be hit-or-miss; they often need multiple dots and still may drop sooner than latex.
• Not reusable—once removed, the dots distort or collect lint.
• They’re not designed for weight-bearing; anything heavier than a few grams is asking too much.
• Paper preservation isn’t their strong suit; the tack can mar delicate surfaces when removed.

Practical tips for better results

• Use two dots for anything heavier than a basic latex balloon, or for longer installations (48 hours+).
• Avoid touching the adhesive; transfer using the liner whenever possible.
• Press and hold for 5–10 seconds to let the adhesive “wet out” on both surfaces.
• Clean surfaces first; a quick wipe dramatically improves adhesion.
• For removal, peel slowly and roll the adhesive off rather than yanking straight away.
• Test on a hidden patch if you’re worried about a finish (especially matte or specialty paints).

Value and packaging

With 200 dots across two small rolls, the quantity feels generous for typical party decor. I used roughly 60 dots for a modest balloon ceiling and a handful of accents; there was plenty left for craft projects. The roll format works, though occasionally the release liner tore when I pulled too quickly—pressing firmly and peeling at a low angle kept the chain of dots intact.

Given how many uses you can get out of a single pack and the convenience of skipping helium or heavier hardware, the cost per use is low. They’re not a substitute for removable hooks or Command-style strips when weight matters, but for lightweight, temporary decor, they fill the gap nicely.

Alternatives to consider

• Painter’s tape: Gentler on paper, but less invisible and weaker on painted surfaces over time.
• Poster putty: Repositionable and good on walls, but more visible and not great for ceilings.
• Removable mounting strips: Stronger and better for heavier items, but bulkier and more expensive.
• Helium: Works for floating balloons, but costs more and offers less control over placement.

The bottom line

These clear glue dots did exactly what I wanted for a small party setup: keep latex balloons on the ceiling for days, hold lightweight decor in place, and come off cleanly from semi‑gloss and gloss surfaces. They stumble on matte walls and textured surfaces, and they can be a touch too aggressive for delicate paper if you plan to archive what you’re hanging. Foil balloons are also a mixed bag unless you double up the dots.

Recommendation: I recommend these glue dots for anyone setting up temporary decorations on smooth, non‑porous or semi‑gloss painted surfaces—especially for balloon ceilings where they shine. They’re affordable, easy to use, and hold up well for multi‑day events. If your walls are matte or textured, or you’re working with keepsake paper items, consider testing first or choosing a gentler adhesive solution.