Features
- Choker-style web anchor strap with large and small D-rings
- Can be used as a vertical or horizontal temporary anchor point around beams, posts, or other structural members
- 1.75 in (44 mm) polyester webbing strength member
- 2.75 in (70 mm) polyester webbing wear pad for abrasion protection
- Polyester webbing treated for resistance to oil, dust, and water
- Rated for 5,000 lb (23 kN) anchor point
- Compact, lightweight design
Specifications
Length | 3 ft (0.9 m) |
Width | 1.75 in (44 mm) |
Weight | 1.18 lbs (0.5 kg) |
Minimum Breaking Strength | 5,000 lbs (23 kN) |
Materials | Repellent polyester webbing; polyester wear pad |
Standards/Approvals | OSHA 1910.140; OSHA 1926.502; ANSI Z359.18-2017 |
Upc | 00810091651797 |
Warranty | 2 Year Limited Warranty |
3 ft choker-style web anchor strap intended for temporary fall protection anchorage. It is compact and lightweight and can be wrapped around beams, posts, or other structural members for vertical or horizontal anchor points.
DeWalt Web Anchor Strap - Choker - Large and Small D-Rings with Wear Pad, 3 ft Review
I keep a small bundle of anchors in my fall protection kit, and one of them gets more use than the others: the DeWalt web anchor strap. It’s a simple choker-style sling with a big D-ring on one end and a small D-ring on the other, meant to wrap a beam, post, or pipe and give you a quick, temporary tie-off point. Over several weeks of site work—steel, wood, and pipe—I used it as both overhead and waist-high anchorage. It did exactly what I expect from a temporary connector: fast to rig, confidence-inspiring under load, and compact enough that I stopped thinking twice about packing it.
What it is and how it’s built
The strap uses 1.75-inch polyester webbing as the strength member with a wider 2.75-inch polyester wear pad sewn along the contact area. That wider pad matters: it distributes pressure on edges and takes the brunt of abrasion so the core webbing doesn’t. Both the webbing and pad are treated to shed oil, dust, and water. Hardware is minimal—one large D-ring for your connection and a smaller D-ring that forms the choke when you pass the large ring through it. The assembly weighs about 1.18 lb and runs 3 feet long, which keeps it compact without feeling flimsy.
It’s rated to a 5,000 lb (23 kN) minimum breaking strength and marked as meeting OSHA 1910.140, OSHA 1926.502, and ANSI Z359.18-2017. Labels are clear and durable, with legible inspection info and standards. The stitching is tidy with dense bar tacks at load points, and the D-rings show no rough edges or questionable welds.
Setup and ease of use
Rigging is straightforward:
- Wrap the strap around the structural member with the wear pad facing the contact surface.
- Pass the large D-ring through the small D-ring to create the choke.
- Cinch it snug so the wear pad sits between the strap and the anchor.
- Clip your connector (SRL or energy-absorbing lanyard) to the large D-ring only.
On an 8-inch steel pipe, the strap choked securely and resisted creeping when loaded and unloaded repeatedly. Around a W-beam web and flange, the wear pad made a noticeable difference compared with narrower slings I’ve used—less “biting” into edges and less tendency to migrate. On a 6x6 timber post, the choke held well, though wood fibers can compress; I still prefer to orient it so the load pulls perpendicular to the grain where possible. On a 12x12 glulam, the 3-foot length was simply short; a longer strap would be the right choice there.
A couple of practical notes from use:
- It packs down small and slides into a side pouch easily. I barely notice the weight.
- The large D-ring seats well with standard rebar hooks, double-locking snaps, and SRL swivels. Clearance was never an issue.
- The choke is smooth to tension and easy to break loose after loading—no wrestling to free it at the end of the day.
Performance and safety considerations
I used the strap as an overhead anchor for SRLs and as a waist-height anchor for shock-absorbing lanyards. In both cases, it felt solid, with no signs of slippage when properly tensioned. The wear pad showed light polish after a day on painted steel but no fuzzing or cut fibers. Polyester’s oil and water repellency helped—grit and grime brushed off rather than embedding.
From a compliance standpoint, the 5,000 lb rating and ANSI Z359.18 listing place it squarely in the expected category for temporary anchorage connectors. Remember that the anchor assembly is only part of the equation: the structure you wrap must be capable of resisting the required loads (typically 5,000 lb per user or engineered by a qualified person to at least twice the maximum arresting force). In practice, that means coordinating with site supervision and not guessing at adequacy.
Best practices I followed and recommend:
- Keep the anchor overhead when possible to reduce free fall and swing hazards.
- Protect against sharp edges. The wear pad helps, but it’s not a cut protector; use additional edge protection on sharp or abrasive members.
- Avoid tapered or conical shapes where a choke can walk toward the narrow end under load.
- Do not connect to the small D-ring; it’s part of the choke, not the attachment point.
- Use compatible gear—full-body harness plus an energy-absorbing lanyard or SRL that meets applicable ANSI standards.
Durability and inspection
After multiple days on steel and wood, the strap still looked new aside from light surface scuffs on the pad. I checked the usual suspects: bar tacks remained tight, no popped stitches; D-rings free of nicks or deformation; label clean and readable. The repellent treatment kept mud from embedding in the fibers—hose off, hang to dry, done.
Web anchors live or die on how they handle abrasion. The wider wear pad and smooth stitching transitions minimize snag points. That said, this is still polyester webbing. It’s not edge-rated, heat-resistant, or cut-proof. I wouldn’t use it near torch work or on raw plate corners without a sleeve or corner protector.
Ergonomics and handling
- The 3-foot length hits a nice balance on most beams and small columns—long enough to choke with at least a few inches of tail, short enough not to droop.
- The large D-ring is easy to find by feel with gloves on.
- The package stays compact in a kit; you could carry two or three without clutter.
- The strap lies flat under load and doesn’t twist or roll, which keeps the connection hardware oriented correctly.
Where it shines—and where it doesn’t
Strengths:
- Quick, intuitive setup with clear hardware orientation.
- Wear pad meaningfully increases service life on abrasive surfaces.
- Compact and light enough to keep on-hand, which increases the odds people will actually use it.
- Clear labeling and standards compliance for paperwork and inspections.
Limitations:
- Length. Three feet is versatile, but it won’t wrap larger columns or big timber. If you regularly anchor to 10x10 or larger, plan on a longer sling as well.
- Not for sharp edges, high heat, or aggressive chemicals. You’ll need purpose-built slings or edge protection for those environments.
- As with any choke, it can migrate on tapered members. Choose anchors with geometry that resists walking.
Tips from the field
- Place the wear pad directly over any interface you expect to rub or see motion. It’s easy to misalign if you’re rushing.
- If using with a beam where the choke could ride into a sharp corner, add a simple corner guard; it’s cheap insurance for the webbing.
- Keep a spare. At this size and weight, having a backup means you’re never tempted to compromise when an anchor point is just out of reach.
- Build a pre-use checklist: label legible, no cuts or glazing, bar tacks intact, D-rings round and smooth, and no chemical smells or stiffness that might hint at contamination.
The bottom line
The DeWalt web anchor strap is a well-executed, no-drama temporary anchorage connector. It rigs quickly, holds reliably, and stands up well to real-world surfaces thanks to the wider wear pad and tidy construction. The 3-foot length and compact weight make it a natural addition to a personal kit, and the standards compliance is right where it should be.
I recommend it for crews and individual users who need a dependable, portable way to create temporary anchor points on steel, pipe, or sound timber. It’s especially useful for overhead SRL tie-offs and short-term tasks where a dedicated beam clamp or permanent anchor isn’t practical. The only caveat is length: if your work routinely involves large columns or wide members, pair this with a longer sling to cover those cases. Within its intended scope, it’s a solid, trustworthy tool that encourages correct use by being simple and convenient.
Project Ideas
Business
Rooftop Day-Use Anchor Kit Rentals
Rent turnkey temporary anchor kits to small contractors: strap, harness, lanyard/SRL, connectors, and quick-start compliance guide. Offer same-day delivery/pickup, pre/post-use inspection, and per-day or per-week pricing.
Temp Anchor Install & Compliance Service
Provide on-site selection and installation of temporary anchors for short-duration jobs, with inspection logs, tagging, and OSHA/ANSI documentation. Bill per visit plus a subscription for periodic audits and toolbox talks.
Event/Film Rigging Safety Add-ons
Supply and install temporary anchor points and secondary safeties for lights and overhead accessories using the straps on truss or beams. Package includes gear, certified techs, and compliance paperwork billed per event day.
Curated E-commerce Anchor Kits
Bundle the strap with rated carabiners, anchor connectors, and a storage bag into industry-specific kits (roofing, facilities, telecom). Add QR-linked setup videos and offer B2B discounts and replenishment subscriptions.
Facility Maintenance Safety Subscription
Serve warehouses and plants with a monthly program: temporary anchor provisioning, rotation, inspections, and short training sessions. Charge a flat fee plus consumables, reducing clients’ capital expense and admin burden.
Creative
Camp Haul Station
Use the strap as a protected tree anchor for a lightweight pulley or carabiner to hoist food bags or camp gear off the ground. The wear pad reduces bark abrasion and the choker design keeps the anchor secure. Not for lifting people.
Garage Overhead Organizer
Create temporary anchor points around rafters or beams to hang hoses, cords, or a kayak cradle using rated hardware. The compact strap is easy to relocate as storage needs change. Use for static storage only and verify structure strength.
Photo/Video Safety Tethers
Wrap around truss or beams to anchor secondary safety tethers for lights, booms, or cable runs. The large/small D-rings make clipping quick while the wear pad protects both the webbing and structure. Suitable for securing gear, not suspending people.
Garden/Post Trellis Anchor
Choke the strap around sturdy posts to create clean anchor points for tensioning guide wires or shade sails. The webbing resists moisture and dust, making it garden-friendly. Use only for non-life-safety loads.
Resistance Band Anchor
Anchor resistance bands to a solid post or beam for home workouts without drilling hardware. The strap’s D-rings allow fast length changes and tidy setup. Not for bodyweight suspension or dynamic lifting of people.