energeaster Solid Indoor 14/2 W/G NMB Cable 25ft Coil，Electrical Wire 14 Gauge Wire 2 Conductors Non-Metallic with Ground Wire

A practical 14/2 NM‑B for small indoor runs

I put this 14/2 NM‑B cable to work on a handful of small residential tasks—a new ceiling fan drop, relocating a couple of receptacles on a 15‑amp lighting circuit, and a short attic run to a wall switch. For projects like these, a 25‑foot coil is the right size: enough length to complete a run cleanly without paying for or storing a big spool. In use, it did exactly what I needed it to do: carry power reliably on a 15‑amp branch circuit, with a jacket that pulls smoothly through bored studs and across attic joists.

What it is and where it belongs

This is a solid copper 14/2 NM‑B cable: two insulated 14 AWG conductors (black hot, white neutral) with a solid bare ground laid between them and wrapped in fire‑retardant paper, all inside a white outer jacket. It’s rated 600 V and 90°C, and is intended for dry, indoor residential wiring—walls, ceilings, attics, and the air voids of masonry or tile walls that aren’t wet or damp. In plain terms, it’s the right type of cable for most 15‑amp lighting and general‑use receptacle circuits in living areas. It’s not for exterior runs, wet locations, crawlspaces that qualify as damp, or anywhere conduit or metal‑clad is required by local code.

A quick code reminder: 14 AWG copper is for 15‑amp breakers, not 20‑amp. Even though the insulation is marked 90°C, NM‑B ampacity follows 60°C column limitations at terminations. Treat it like any other 14/2 NM‑B in that regard.

Build quality and jacket feel

The jacket is white (as you’d expect for 14 gauge NM‑B) with a slick, slightly glossy coating. That slickness is a plus when you’re pulling through wood—less friction across studs and holes—especially on longer straight shots. The tradeoff is feel: compared with premium “Romex”‑branded cable, this jacket is a bit stiffer and doesn’t take a set as easily. It has more coil memory coming off the bundle, so managing the first few feet requires a little patience and uncoiling rather than tugging.

Inside, the copper conductors are true to gauge, round, and consistent. The ground is bare copper wrapped in paper, which tears away cleanly when you open the jacket. I didn’t find flat spots or off‑center conductors—tolerances seem fine for reliable stripping and terminations.

Installation experience

• Pulling: The low‑friction jacket paid off for me in the attic, where I ran about 18 feet across joists and down a stud bay. It slid easily, and I didn’t feel the need for fish tape beyond a short push stick. Through tight 3/4‑inch bores, it fed without chatter or snagging.

• Stripping: The outer jacket is on the tougher side. A basic NM cable ripper worked best—one clean bite and a firm pull. Trying to zip it open with a utility knife took more effort than with softer jackets and increases your odds of nicking insulation. Once open, the individual conductor insulation strips cleanly with a 14 AWG notch on a good pair of strippers. Notably, the conductor insulation feels a hair tougher than some premium lines; adjust your technique to avoid scoring.

• Bending and termination: The stiffness shows up most in crowded boxes. You can make the bends you need, but it resists tight radii and doesn’t “stay” in a bend as willingly as a more supple jacket. Pre‑forming gentle bends outside the box helped. Under binding head screws and in back‑wire clamps, the copper seated firmly and didn’t deform.

• Staples and support: Standard NM staples fit fine; don’t overdrive them on this jacket—snug is enough. The slightly stiffer sheath makes overdriving more obvious, which is actually a helpful feedback loop to avoid pinching the cable.

• Labeling and identification: The white jacket is a clear visual cue for 14 gauge in mixed runs, which I appreciate for quick identification alongside 12/2.

Performance and safety

On short runs typical of a 25‑foot coil, voltage drop isn’t a concern, and this behaved as expected under a combination of lighting and a ceiling fan motor load. I saw nothing unusual with heat buildup in attic sections during a warm afternoon; the 90°C insulation rating provides a comfortable margin even though you size the circuit at 60°C.

As with any NM‑B, keep it out of wet or damp locations. If you must transition outdoors or into areas subject to moisture, switch to a wet‑rated wiring method and enclosures per local code. If you’re bundling multiple current‑carrying conductors or passing near heat sources, mind derating and spacing.

Length, packaging, and handling

This comes as a 25‑foot coil rather than on a spool. The coil was taped adequately and the ends were easy to locate, but like most coil‑packaged NM‑B, it carries memory. I recommend unrolling it like a garden hose—rotate the bundle and walk it out—rather than pulling from the center. Five extra minutes at the start saves wrestling later and reduces the tendency for kinks.

For quick projects, this length is efficient: less waste, less storage, and likely cheaper per project than buying a 50‑ or 100‑foot roll you’ll only partially use. For anything beyond a couple of runs, step up in length; constantly splicing 25‑foot sections isn’t worth it.

Value

Cost is where this cable shines. It does the fundamental job of NM‑B—safe, code‑appropriate power distribution on 15‑amp indoor circuits—without the premium price of the softest, most pliable jackets. If you’re wiring a room or tackling a few additions, the savings are real. If your workday is nothing but repetitive pulls through tight boxes where speed and pliability rule, premium cable can be worth the extra few dollars. For typical homeowner and light pro use, this strikes a sensible balance.

Where it falls short

• Jacket stiffness: It’s stiffer than some name‑brand alternatives. In cramped boxes or around short radii, it takes more persuasion and doesn’t hold a shape as readily.

• Tough jacket to open: The outer sheath resists casual knife scoring. Use a cable ripper and you’ll be fine; rely on a knife and you’ll spend extra time and increase nick risk.

• Coil memory: As a coil pack, it wants to spring back until you unroll it properly. Not unique to this product, but more noticeable with a firmer jacket.

• Not for damp/wet locations: True of all NM‑B, but worth repeating if you’re mixing wiring methods in a remodel.

I’d also flag that I didn’t see footage markings on my coil. That’s common on short lengths, but it means you’ll measure runs manually.

Tips for smoother installs

• Warm it up: If you’re working in a cold garage, bring the coil inside for an hour. Warmer jacket equals better pliability.

• Unroll, don’t yank: Spin the coil and walk it out to minimize twist. It reduces fight at terminations.

• Use a cable ripper: One squeeze and pull; skip the deep knife cuts.

• Pre‑bend outside the box: Shape your conductors to their destination, then land them. It’s cleaner and faster with a stiffer cable.

• Mind box fill: The slightly bulkier feel makes tight boxes feel tighter. Choose an appropriately sized box and count your conductors carefully.

The bottom line

I’m satisfied with this 14/2 NM‑B cable for indoor residential work. It pulls smoothly, terminates reliably, and carries its 15‑amp duties without drama. The jacket is stiffer than premium options, and the sheath takes a deliberate hand to open, but neither trait is a deal breaker if you use the right tools and techniques. The 25‑foot coil is a practical size for ceiling fan drops, short lighting runs, and one‑off receptacle additions, and the price makes sense for those projects.

Recommendation: I recommend this cable for budget‑conscious DIYers and pros who need a solid, code‑appropriate 14/2 NM‑B for small indoor runs and don’t mind a slightly stiffer jacket. If ultimate pliability and fastest stripping are your top priorities—say, you’re wiring multiple boxes all day—consider spending a little more on a softer‑jacketed line. For everyone else, this cable is a dependable, cost‑effective choice that gets the job done cleanly and safely.