HOMOTEK 4 Pack Closet Door Finger Pull 2-1/16”, Easy Snap in Installation, Black, Fits a 5/16”Depth x 2-1/16" Diameter Opening Hole

What I tested

I replaced a set of dated brass inserts on two bypass closet doors and also used a pair to cover the old knob bores on a repurposed interior slab I’m using as a simple barn-style slider. In both cases, I installed the HOMOTEK finger pulls in matte black. The pack includes four steel pulls—enough to do both sides of two doors or both faces of a single through-bored slab.

Design and build quality

These are classic recessed finger cups: a rolled outer lip, a shallow cup, and springy retention tabs around the perimeter. The cups are steel rather than thin stamped tin, which gives them a reassuring stiffness when you press them in and when you pull the door later. The matte black finish looks modern without flashing light, and the sheen is consistent across all four units I installed. Edges are clean and comfortable—no burrs or sharp spots on my set.

If you prefer other looks, the line is available in multiple finishes (satin nickel, oil-rubbed bronze, brass, antique brass). The variety matters because you’ll often be matching other nearby hardware; it’s nice not to be locked into a single color.

Sizing and fit

The outer lip measures roughly 2-7/16 inches, sized to cover a standard 2-1/8-inch bore (the same size as a typical doorknob hole). The cup depth is about 5/16 inch. That depth is appropriate for sliding panels where you just need a fingertip recess to open and close—not a deep pocket pull.

On my bypass closet doors, the existing routed pockets were already the right diameter. The fit was snug enough that the pulls seated flush with a firm push. On the repurposed door with an old knob bore, the pulls covered the hole perfectly from each face. If you’re working with doors that have seen multiple hardware swaps and the bore is a little oval or oversize, plan on either gently bending the retention tabs out a touch or adding a thin wrap of painter’s tape inside the hole to tighten the fit. On one door, I splayed two tabs slightly with needle-nose pliers for a rock-solid hold.

A quick note on measurements: closet pulls are surprisingly sensitive to 1/16-inch differences. If you’re drilling new pockets, a 2-1/8-inch hole saw or Forstner bit with a depth stop set to 5/16 inch will give you a precise, repeatable recess. If your opening is 2-1/16, these can still seat with a few light taps, but I’ve had the most consistent results with a true 2-1/8-inch cut.

Installation experience

This is one of those “five minutes, actual” tasks:

• Pop the old pulls out with a flat screwdriver or putty knife, working around the lip to avoid marring the door.
• Clean any dust or paint lips in the pocket.
• Align the new pull square to the hole and press in by hand. If it stalls a millimeter proud, a wood block and a couple of taps from a rubber mallet seat it perfectly.

No screws, no nails, no adhesive required. The spring tabs do the work. I did all four in under ten minutes, including a quick clean-up of the routed pockets.

If a pull doesn’t want to stay put because the hole is slightly oversized, you have options before reaching for glue. Carefully flex a couple of tabs outward to increase their bite, or apply a very thin bead of clear construction adhesive as a last resort. I only needed to tweak tabs on one of the four.

Everyday use and ergonomics

The recess depth is shallow by design, but it’s adequate for one- or two-finger control of most sliding doors. On hollow-core bypass panels and lighter barn-style doors, I can hook a fingertip easily, even when my hands are a bit damp. The rolled edge is comfortable and doesn’t chew at your fingertip the way some sharp-edged cups can.

For extra-heavy slabs or doors with tight tracks, I’d still pair these with an edge pull on the strike side to get better leverage. These cups aren’t meant to be your only handle for moving a 100-pound slab against a gasket. For typical closets and furniture sliders, though, they do exactly what they should: give you a clean, low-profile grip without protrusions.

Durability and finish

After several months of daily use, the matte black finish on my set is holding up with no obvious scratching or chipping. Because they’re steel, they feel sturdier than flimsy aluminum cups I’ve used in the past. Like any painted finish, they can pick up a mark if you hit them with a metal ring or a key, so avoid seating them with a metal hammer directly on the lip. Use a wood block or a cloth barrier if you need to tap them in.

Indoors, corrosion isn’t a concern. I wouldn’t spec them for exterior use or high-humidity commercial showers, but that’s outside their intended scope anyway.

Where they shine

• Quick replacements: Swapping out dated brass cups on sliding closet doors is as straightforward as it gets. These transform the look in minutes.
• Covering old knob bores: If you’re converting a repurposed door to a slider, a cup on each face neatly covers a 2-1/8-inch through-bore and gives you a functional pull on both sides.
• Clean, low-profile aesthetic: The thin lip and consistent finish blend into modern and transitional interiors without calling attention to themselves.
• Value in a four-pack: Four pieces cover both faces of two panels, or two faces of a single through-bored slab, without having to buy multiple small packs.

Where they fall short

• Limited adjustability: The snap-in tabs are simple and effective, but there’s no screw-in option. On oversize or damaged bores, you might need to bend tabs or use a dab of adhesive.
• Not for very heavy doors: The shallow recess isn’t the right tool to muscle a heavy slab across weatherstripping. Pair with an edge pull in those cases.
• Measurement ambiguity: You’ll see both 2-1/16 and 2-1/8 inches mentioned in various places. In practice, a 2-1/8-inch bore has been the most reliable fit in my installs. Measure before you cut.

Tips for best results

• Use a Forstner bit for new installs. It leaves a cleaner shoulder than a hole saw and helps the lip sit flush.
• Seat with a wood block. A couple of gentle taps prevent finish marring and ensure even pressure on the tabs.
• Paint first, install last. If you’re painting the door, finish the coat and light sanding before inserting the pulls to avoid getting paint on the lip.
• Check both sides. If you’re covering a through-bore, make sure the inner face sits flush as well; slight differences in door skin thickness can show if one side isn’t fully seated.

Value

Against big-box two-packs, this four-pack is cost-effective and practical. The steel construction and consistent finish give it a leg up over cheaper, thinner cups I’ve tried, and the snap-in design truly saves time. Given the small price delta between finishes, I’d select based purely on match with your hinges, track hardware, or other nearby fixtures.

Alternatives

If you need a deeper grip or a locking function, look at pocket door edge pulls with integrated latches—they serve a different use case. If your bores are damaged or irregular, a pull with screw flanges or a larger outer lip might be a better choice. For exterior or wet environments, stainless hardware is safer than painted steel.

Bottom line

The HOMOTEK finger pulls get the basics right: solid steel, clean finish, accurate sizing, and fast, tool-free installation. They’re a straightforward upgrade for tired closet doors and a tidy solution for covering old knob bores on repurposed sliders. While the snap-in tabs leave little room for adjustment on damaged holes, a minor tweak with pliers solved the only fit issue I encountered.

Recommendation: I recommend these for most interior sliding doors—closets, wardrobes, and light barn-style panels—especially if you’re after a quick, modern refresh in a consistent finish. They install in minutes, feel sturdy in use, and the four-pack format makes practical and financial sense for real-world projects. If you’re working with oversized or chewed-up bores or you need a pull for a very heavy slab, consider a model with screw-fastening or a deeper grip; otherwise, these are an easy win.