PRIME-LINE K 5007 Screen and Storm Door Push Button Latch Set With Night Lock, Fits Doors 5/8 – 1-1/4 In. Thick, Black Finish

What I tested

I installed the Prime-Line K 5007 latch on an older outswinging storm door that lives on a side entry—medium use, a handful of cycles a day. The original latch had worn to the point of not catching reliably, so I wanted a straightforward, affordable swap that didn’t require drilling new holes or replacing the whole door.

The quick take

The K 5007 is an inexpensive, near-universal push-button latch set that generally delivers what it promises: it fits common hole spacing, works on left- or right-hand doors, includes a forgiving spring-loaded strike, and adds a simple “night lock” to block the outside button. Installation is beginner-friendly as long as you’re willing to trim the spindle to length. The tradeoff is durability. The handle body is aluminum, but the push button and internal actuator are plastic, which puts a ceiling on how “solid” it can feel and how long it will survive heavy, frequent use. For light-to-moderate traffic doors, it’s a sensible budget fix. For a front-entrance workhorse, I’d look at heavier-duty alternatives.

Installation experience

Swapping this in was fast, but only after I took the time to size the spindle correctly.

• Door compatibility: The set is designed for 5/8 in. to 1-1/4 in. thick outswinging wood or metal screen/storm doors. Mine is just under 1 in. thick.
• Hole spacing: The inside latch uses 1-3/4 in. screw spacing. That matched my door, which meant no new drilling.
• Non-handed: It works on both left- and right-hand outswingers. I didn’t need to reorient anything.

The only “hands-on” step is trimming the square post (spindle). Out of the box, it’s intentionally long to cover the thickness range. If you don’t trim it, the inside lever can bind and the latch won’t release cleanly. Here’s what worked well:

1. Dry-fit the outside handle and inside latch without screws to gauge spindle protrusion into the latch body.
2. Mark the spindle so it extends only a few millimeters past the latch opening when the handles are seated—too long and it binds; too short and the button won’t engage.
3. Cut with a hacksaw and clean the edges with a file so it slides smoothly.
4. Reassemble and test before final tightening.

Prime-Line includes the fasteners and the directions are straightforward. From first screw to last tweak, I spent about 20 minutes, with most of that spent trimming and test-fitting the spindle.

Build and design

• Materials: The handle housings are aluminum with a black finish. The exterior button and internal actuator components are plastic. That combination keeps the price down and the weight low, but the button doesn’t have the solid, “dead-metal” feel of premium latches.
• Strike: The included strike is a spring-loaded bar. That’s a thoughtful choice for older doors where alignment isn’t perfect; the spring allows a bit of give as the latch engages and helps the door catch without having to slam it.
• Night lock: Inside, there’s a simple slide that disables the outside push button. It’s not keyed and not a security deadbolt; it’s there to keep the door from opening from the outside when you’re home.

Fit and finish were clean on my set. The black coating is even, and the parts mate without gaps or burrs. The included screws are typical of this category—perfectly serviceable for wood jambs and thin metal skins.

Fit and compatibility notes

• Door thickness: Works across 5/8–1-1/4 in. doors, as claimed. If your door is thicker, look elsewhere.
• Hole pattern: If your existing interior plate uses 1-3/4 in. spacing, you’re in good shape. If not, you’ll need to drill new holes or choose a different model.
• Outswing only: This is meant for outswinging screen and storm doors.
• Left/right: Truly non-handed; no oddball flipping required.

The spring strike did a lot to mask the minor warps and seasonal changes in my old frame. If your door or jamb has more serious misalignment, plan on shimming the strike slightly or adjusting your closer so the door seats positively without excessive force.

In daily use

The action on the K 5007 is light and predictable. Pressing the exterior button or flipping the interior lever gives a quick, short throw that pops the door free without needing a yank. The spring-loaded strike helps the door re-latch quietly on close—less rattle than fixed strikes I’ve used. I adjusted my closer so the last inch of travel is gentle; that keeps the latch from taking a beating.

Two cautions if you want it to feel “right”:

• Don’t overtighten the mounting screws. Cranking down can distort the handle body slightly and introduce drag on the actuator.
• Make sure the spindle is cut square and deburred. A rough or slightly angled cut can cause the plastic actuator to rub and stick.

The night lock is convenient for quick privacy or to keep the door from being opened from the outside if you’re airing the house out. Again, it isn’t a security device; treat it as a courtesy lock for a screen door.

Durability expectations

This is the part where price and materials show. The aluminum handle shells resist corrosion and look fine after handling, but the internal push-button components are plastic. Used thoughtfully—no slamming, no leaning on the button—the latch works as expected. In a high-traffic location where kids or tenants are likely to mash the button hard and often, I’d expect accelerated wear, potential sticking, or eventual failure of the actuator.

A few maintenance habits go a long way:

• Keep the latch and strike clean. A blast of compressed air and a drop of dry lube twice a year keeps grit from grinding the plastic.
• Re-check the closer. If the door is slamming, your latch is doing more work than it should.
• Confirm screws are snug. Vibration can loosen hardware, which leads to misalignment and binding.

If you want a latch that shrugs off abuse for years, look for one with a metal internal actuator and a beefier strike. If you’re updating a lightly used side door or a porch entry, the K 5007 is serviceable and cost-effective.

What I liked

• Universal fit: The 1-3/4 in. interior spacing and trimmable spindle made it a true drop-in for my door.
• Spring-loaded strike: More forgiving than a fixed lip; doors close more quietly and latch more reliably.
• Non-handed design: No reconfiguration required for left/right installations.
• Installation simplicity: Minimal tools, clear instructions, and an easy path for DIYers.
• Night lock: Handy for preventing outside access without a key mechanism to fuss with.

Where it falls short

• Plastic internals: The button and actuator don’t have the longevity or feel of metal. Treat it gently.
• Not a heavy-duty latch: Fine for low-to-moderate use; not ideal for a main entry that sees constant traffic.
• Setup sensitivity: If you don’t trim the spindle correctly or you overtighten the mounting screws, you’ll introduce binding and frustration.

Who it’s for

• Homeowners needing a quick, inexpensive replacement for a failing screen or storm door latch.
• DIYers looking for a near-universal fit on older doors without re-drilling.
• Light-to-medium traffic doors where the convenience of a push-button and night lock is enough.

Who should look elsewhere: landlords and anyone outfitting a main, high-use entrance. Spend more for an all-metal actuator and a heavy-duty strike.

Recommendation

I recommend the K 5007 for budget-conscious replacements on light- to medium-use outswinging screen or storm doors. It installs quickly, fits a wide range of doors without drama, and the spring-loaded strike helps older frames latch reliably. Just go in with realistic expectations: the plastic actuator limits longevity, and it’s not built for the kind of abuse a front entrance sees. If that tradeoff suits your door and your usage, this latch is an easy, economical fix. If you need “set it and forget it” durability under heavy traffic, step up to a model with metal internals instead.