ECUDIS Swag Light Kit, Lamp Parts Chandelier Light Fixture Chain Swag Kit Includes 12 Ft Chain, 15 Ft Cord with Switch, 2 Swag Hooks and Mounting Hardware

I needed a straightforward way to hang a pendant over a rental dining nook without touching the hardwiring, so I put this ECUDIS swag kit to work. After a weekend project and a few weeks of living with it, I’ve got a clear picture of where it shines and where it comes up short.

What you get and first impressions

In the box: a 12‑foot metal chain, a 15‑foot plug‑in lamp cord with an inline on/off switch, two swag hooks, and basic mounting hardware. The chain links are consistent and free of burrs, the finish on my nickel set looked even, and the cord jacket is smooth and flexible. It’s a no-frills kit, but it covers the essentials for suspending and powering a pendant or small chandelier without opening a junction box.

The chain is rated to 35 pounds, which is generous for most single‑shade pendants and light DIY fixtures. As always, remember that rating applies to the chain—your ceiling anchors and substrate matter just as much.

Installation experience

Setup is refreshingly simple if you’re handy with the basics:
- I marked my fixture centerline over the table, then planned the “swag” route from the outlet up the wall, across the ceiling, and down to the fixture.
- One hook went near the wall, the other above the fixture location. I prefer hitting a joist with at least one hook; if you’re in drywall, use proper toggle anchors (the kit’s anchors are fine for light loads, but I keep a better set on hand for peace of mind).
- Using two pairs of pliers, I twisted open a link to detach the chain to my exact length and closed it back up. No need to stretch links—twist them sideways to keep their strength.
- I threaded the cord through the chain every few links to keep things tidy, leaving a bit of slack near the fixture as strain relief.
- With hooks set and chain hung, I connected the pendant to the chain and plugged in the cord. The inline switch controls power; there’s no dimming in the box.

Total time: under an hour, including measuring and careful drilling. If you’re converting a new pendant to a plug‑in setup, budget a bit more for wiring and canopy cleanup.

Design and build quality

• Chain: Sturdy for the category and looks more substantial than the cord—exactly what you want in a visible suspension system. The nickel finish reads as a neutral satin, not mirror‑shiny, and blends easily with brushed hardware.
• Cord: Functional and flexible, but on the slimmer side. It’s likely an 18 AWG SPT‑1 style; perfectly adequate electrically for a typical pendant load, but aesthetically fine rather than premium. If you’re aiming for a decorative, statement look, a cloth‑braided cord would elevate things.
• Switch: The inline switch does the job and is quick to wire at the factory, but it’s the insulation‑piercing type. It worked for me, though it feels like the weak link in an otherwise solid kit. I prefer screw‑terminal inline switches for long‑term reliability and would happily swap it if this were a permanent setup.

Overall, it’s a practical, budget‑minded bundle that prioritizes function over flourish. That’s not a knock—just set expectations accordingly.

Adjustability and reach

The 12‑foot chain plus 15‑foot cord gives you generous routing options. I had no trouble running from a floor outlet, up the wall with clear cord clips, and across a 9‑foot ceiling. Height adjustment is straightforward: shorten the chain, coil excess cord behind furniture or along the wall, and position the switch where it’s convenient to reach. The combination makes it renter‑friendly and forgiving if your outlet and light placement aren’t ideal.

Safety and load considerations

The 35‑pound chain rating is the headline, but a few practical points matter more:
- Always anchor at least one hook into solid wood if your fixture is heavy or broad. Toggle anchors in drywall can hold surprisingly well, but joists beat hollow cavities every time.
- Keep fixture weight reasonable. I’m comfortable up to the mid‑20‑pound range with mixed substrates (joist plus drywall), but I stay conservative with fully hollow‑wall installs.
- Watch wattage and heat. This is a plug‑in cord designed for typical pendants and small chandeliers. High‑wattage multi‑lamp fixtures increase current and heat—keep it sensible and use LED bulbs to stay cool and efficient.

Everyday use

Once up, the kit disappears into the background—which is exactly what I want from a swag setup. The chain carries the visual weight; the cord reads as a neat line. The inline switch has a light, clicky action. It works, but it doesn’t inspire confidence the way a good toggled socket or wall switch does.

Two small quality‑of‑life tweaks made the setup nicer:
- I added a smart plug so I can control the light from my phone and leave the inline switch in the “on” position.
- I used slim, clear clips along the wall to guide the cord straight up to the ceiling. It’s a tidy, rental‑friendly touch.

Where it excels

• Quick conversions: If you’ve got a hardwired pendant you love and want a plug‑in solution, this covers the essentials without a trip to multiple stores.
• Renter‑friendly installs: No hardwiring and minimal patchwork when you move out—two small holes can be easily filled.
• Generous length: The chain and cord length gives you flexibility to center a light where you need it, even if the nearest outlet isn’t ideally placed.
• Value: You get the core components at a fair price, and nothing feels flimsy where it counts—the chain and hooks behave as they should.

Where it could be better

• The cord looks and feels basic. It’s fine functionally but won’t satisfy design‑forward setups where the cord is part of the aesthetic.
• The inline switch is the simplest type and, while functional, isn’t my favorite for long‑term use. A screw‑terminal switch would be a welcome upgrade.
• Hardware assortment is basic. It works, but if you’re dealing with old plaster, heavy lath, or crumbly drywall, bring your own anchors.

Tips for a cleaner, safer install

• Use two pliers to twist chain links open and closed—don’t pry them apart.
• Add a small zip tie or cord grip near the fixture canopy as strain relief so the cord isn’t bearing weight at the electrical connection.
• Aim one hook into a joist. If you can’t, use quality toggle bolts rated for your fixture’s weight.
• Consider a smart plug or a higher‑quality inline switch to avoid wear on the included switch.
• If aesthetics matter, sleeve the cord in a fabric cover or replace it with a cloth‑braided cord—this kit’s chain plays nicely with upgrades.

The bottom line

The ECUDIS swag kit does exactly what it promises: it lets you hang and power a pendant or small chandelier cleanly, safely, and without opening a junction box. The chain is sturdy, the lengths are generous, and the mounting process is straightforward. The trade‑offs are in the finishing touches—the cord is slim and functional rather than decorative, and the inline switch is the simplest execution of its kind.

Would I recommend it? Yes, with context. If you need an affordable, reliable way to convert or hang a light in a rental or a flexible space, this kit is a solid pick. It holds up well for everyday use, installs easily, and gives you plenty of reach. If you want a premium look out of the box or plan to hang a particularly heavy, multi‑light fixture, consider pairing the chain with a nicer cord and switch or shopping a higher‑end kit. For most DIYers and renters, though, this hits the sweet spot of function, safety, and value.