YiePhiot Mini Ceiling Wall Projector Mount Stand Compatible with QKK, DR.J, DBPOWER, Anker, VANKYO, AAXA, Jinhoo, PVO, TMY, AuKing and Most Other Mini Projector

Why I picked up this mount

I needed a simple way to get a small projector off a cart and onto the ceiling of a multipurpose room—nothing fancy, just a clean, compact solution that wouldn’t cost more than the projector itself. The YiePhiot mini projector mount caught my eye because it promised the basics: a short drop (about 175 mm), a ball-joint for angle adjustments, and a set of thread adapters to cover the usual projector tripod holes. After a few weeks of use with a couple of different mini projectors, I have a clear sense of where it excels and where you’ll want to temper expectations.

Design and build

The mount is light, compact, and straightforward. It’s a simple three-part assembly: a base plate for the wall or ceiling, a short hollow pole, and a ball-joint head with a tightening knob plus interchangeable screws/adapters. The finish is a matte black that blends into most ceilings and doesn’t call attention to itself.

Materials-wise, the core parts are metal, and the overall feel is better than the price might suggest—but it’s still very much a budget mount. The pole and head don’t flex under the weight of a typical mini projector, but there’s less inertial resistance here than you’d get from a heavier, more expensive mount. The rated load is 5 kg. Personally, I wouldn’t go anywhere near that number; for best results, I’d keep it to 2 kg or under. That keeps the ball-joint from creeping and makes alignment stick.

The included adapters cover common thread sizes for small projectors: 1/4"-20 (6.35 mm), 6 mm, and a smaller just-under-4 mm option. If your projector has a standard tripod socket, you’ll be fine.

Compatibility and fit

I tried the mount with two devices:

• A 1.3 kg mini projector with a 1/4"-20 threaded insert.
• A 2.4 kg compact 1080p projector using the 6 mm adapter.

The included hardware covered both without fuss. Do note that this mount only works with projectors that have a bottom-mounted tripod screw hole. Some compact projectors don’t have that—so check your unit before you buy. There’s no multi-arm plate here; it’s a single-point connection by design.

The 175 mm drop (about 6.9 inches) is enough to clear light fixtures and get below decorative trim in many rooms, but it doesn’t replace a true drop pole if you need significant clearance for keystone alignment or to hang below a conduit run.

Installation experience

Installation is as no-nonsense as it gets. The head assembly unthreads from the pole, and the pole unthreads from the base plate, so you can mount the plate first without fighting a dangling assembly over your head. I tried two approaches:

• Into a ceiling joist: pilot holes and wood screws.
• Into drywall: toggles on the base plate holes.

Both worked, but if you’re going the drywall route, consider upgrading the included anchors. The supplied screws and anchors will get the job done for very light loads, but they’re soft and not confidence-inspiring. Using quality toggles or tapping into a stud is a better plan—especially if you’ll be aiming horizontally.

Once the base plate is up, you thread the pole back in, add the ball head, and choose the right adapter for your projector’s thread. The whole process took about 15 minutes.

Tip: before you snug the projector all the way onto the thread, back the tightening knob out a bit so the ball-joint is loose. That makes it easier to get the final angle, and then you can lock the head in place.

Adjustability and alignment

The head offers 90 degrees of tilt and a full 360 degrees of rotation. Rather than separate adjustments for pitch, roll, and yaw, you get a single ball-joint locked by one knob. That keeps the design simple, but it also means fine-tuning is more fiddly. It takes a couple of tries to land on the exact position you want, especially if you’re dialing in tiny corrections to remove keystone.

With the 1.3 kg projector, once tightened, the position held well—no sag or drift over several days. With the 2.4 kg projector, I noticed two quirks:

• If I didn’t torque the knob firmly, the head could creep a couple of degrees over time.
• There’s a touch of play in the rotation axis. It’s not a loose rattle, but it’s enough that a nudge can shift your alignment if the knob isn’t properly cranked down.

Neither of these were deal-breakers, but they confirm my view that this mount is happiest with lighter gear and mostly static setups.

Real-world use

I ran one installation pointing straight down over a cutting table, and another horizontally to a wall screen. Straight-down deployment is this mount’s sweet spot: the weight hangs cleanly on the joint, and it holds alignment without drama. Horizontal projection asks more of the head—gravity isn’t helping you—so take the time to tighten the knob fully. A small flat washer between the head and projector base (if your projector design allows it) can increase friction and reduce micro-movements.

The short drop keeps the setup tucked close to the ceiling, which I liked in a lower room. It also means cable runs are easy to tidy; a small adhesive clip on the pole keeps HDMI and power routed neatly to the base plate.

Where it falls short

• No micro-adjust: A single ball-joint means you can’t independently tweak pitch, yaw, and roll. If you’re tuning a permanent home theater and want pixel-perfect alignment, a mount with separate axis locks is a better fit.
• Limited hardware quality: The included screws and anchors are serviceable but soft. I swapped in better fasteners for peace of mind.
• Short drop only: 175 mm is fixed. If you need a longer or adjustable pole, look elsewhere.
• Heavier loads press the limits: It’s rated for 5 kg, but in practice it’s much more confidence-inspiring under 2 kg.

Who it’s for

• Great for: Mini projectors, small rooms, workshops, classrooms, and any setup where you want a light, unobtrusive mount and a fixed position. Downward-facing use (over a table or work surface) is especially problem-free.
• Not ideal for: Large or heavy projectors, frequent re-aiming, or installations that demand fine-grained alignment controls. If your projector lacks a tripod socket, this mount won’t work.

Tips to get the best results

• Mount into solid backing whenever possible—hit a joist or use proper toggles.
• Keep the projector weight modest; under 2 kg is the sweet spot.
• Tighten the ball-joint firmly; a small dab of medium threadlocker on the knob’s threads can help prevent loosening over time.
• Pre-aim the projector before fully tightening, then do final tweaks with the image on-screen.
• Consider upgrading the included anchors and screws if you’re mounting into drywall.

Value and alternatives

At its price, the YiePhiot mount punches above its weight. It’s a clean, minimalist solution that does the basic job without fuss. If you need more precision, you’ll find pricier mounts with separate adjustments for pitch/roll/yaw and longer extension options. Those do make alignment easier, but they’re overkill for a lightweight projector in a casual space. If your use case is a dorm, a craft room, or a small office, this mount captures most of the utility at a fraction of the cost.

Recommendation

I recommend the YiePhiot mini projector mount for light, mostly fixed installations using small projectors with a standard tripod thread. It’s easy to install, compact, and holds position well with sub-2 kg loads—especially for downward-facing setups. You’ll want to bring your own quality anchors or screws and accept that fine adjustments are more hands-on than on premium mounts, but at this price, the trade-offs feel fair. If your projector is heavier or your installation demands precision alignment and a longer drop, step up to a more robust, multi-axis mount. For everything else, this one gets the job done simply and affordably.