khtumeware 10 Pack 3" Drawer Pulls Antique Brass Cabinet Cup Pulls Kitchen Hardware Cabinet Handles Drawer Handles Knobs 3 inch Hole Center

A simple swap that looks anything but simple

Hardware changes are one of the quickest ways to refresh cabinetry, and my latest kitchen refresh used a 10-pack of Khtumeware cup pulls in antique brass. These are classic bin-style pulls with a 3-inch center-to-center spacing and a semi-recessed grip. I installed them on a mix of drawers and smaller cabinet doors to replace a mix of aging knobs and tired bar pulls. The difference was immediate: warmer tone, more cohesive lines, and a subtly vintage look that doesn’t feel dated.

Build quality and finish

Out of the box, the pulls feel reassuringly substantial. They’re not the thin, “tinny” sort you sometimes get in budget sets; there’s real heft here, and the cup walls don’t flex. The finish on the antique brass reads as a warm, brushed brass with a muted sheen—more champagne than yellow. Under daylight it appears slightly brighter than it does in product photos, which worked to my advantage, as it brought warmth without tipping into the overly brassy, high-gloss territory that can clash with modern fixtures.

Finish consistency across the ten pieces was very good. I looked closely for color drift between pulls and for any obvious swirl marks or lacquer drips. Minor micro-variations are expected with antiqued finishes, but the set I installed presented a uniform tone and a clean brushed texture. The interior of the cup is smooth with no burrs, and the front edge is slightly eased, which helps both comfort and the overall look.

Installation experience

These use a standard 3-inch (76 mm) center-to-center spacing, which is still one of the most common specs for cabinetry. If you’re replacing existing pulls with the same spacing, installation is as simple as backing out the old hardware and driving in the new. If you’re drilling new holes, a cabinet hardware jig is your friend here—especially with cup pulls. The curved body makes it harder to visually “eyeball” level compared to a straight bar, and a small misalignment shows.

A few notes from my install:

• The package included two screw lengths, which covers most common drawer front thicknesses. I used the shorter screws on 3/4" doors and the longer ones on 1" drawer fronts. If your drawer boxes are thicker or you have applied faces, measure before drilling.
• Threading feels snug. On a few, I had to back the screw out and re-seat it to avoid cross-threading. Pre-threading the screws into the pull before mounting helped.
• Cup pulls can “telegraph” slight hole errors. If your holes are a hair off, the pull may appear crooked even if the bubble level says otherwise. A jig removes that guesswork.

From first pilot hole to the last pull, the full set took me a little over an hour, including measuring and adjustments. That’s markedly faster than finishing a coat of paint, and the payoff is more dramatic than you might expect.

Ergonomics and daily use

Ergonomically, these are well-considered. The semi-recessed grip gives enough finger clearance for adult hands on standard-depth drawer fronts. The inner surface is smooth and comfortable; there’s no sharp edge biting into fingertips. On very shallow top drawers right under a countertop overhang, cup pulls sometimes feel tight. I tried one in that position as a test, and it was still usable, but I preferred a knob there for maximum clearance; everywhere else, the cup pulls felt natural and were easy to grab.

Noise-wise, the metal-to-wood contact is minimal because of the standoff created by the screws and the geometry of the cup. They don’t clack or buzz against the drawer face.

Style and pairing

Visually, these land in that “modern classic” zone: the silhouette is traditional, but the brushed antique brass keeps it current. I paired them with simple round knobs in a similar tone on upper cabinet doors, and the blend works—cohesive without being matchy-matchy. The finish plays nicely with warm woods and also adds welcome contrast against painted cabinets in off-whites, sage, and deep blues. If you’re mixing metals, they sit comfortably alongside satin nickel or stainless appliances, provided you repeat the brass in a couple of other spots (lighting, faucet, or a frame) to make it feel intentional.

Durability so far

After several weeks of heavy kitchen use, I’m not seeing premature wear. No color rub-off on high-touch edges, and the brushed surface is forgiving of fingerprints. I did a quick wipe-down test with a mild dish soap solution and a microfiber cloth; the finish cleaned easily without streaking. I’d avoid scouring pads, harsh chemicals, or ammonia-based cleaners, which can dull plated finishes over time. If you like the idea of a patina developing, these read more “sealed” than raw, so don’t expect rapid aging; they’re designed to hold their look.

The small stuff that matters

A few quality-of-life touches stood out:

• All pulls shared the same hole spacing precisely. I checked a few with calipers because off-spec spacing is a common frustration; no issues here.
• The backs are cleanly cast and labeled, which sounds minor but helps keep orientation consistent during install.
• The front edge has just the right radius to catch light without looking flashy, which elevates the look on otherwise plain slab drawers.

Minor drawbacks

No product is perfect, and there are a couple of quirks to note:

• Thread tolerance can be tight. If you push the screw at an angle, it’s easy to start it crooked. Go slow, pre-thread, and avoid overtightening. A handheld screwdriver gives better feel than an impact driver here.
• As with many cup pulls, installation is less forgiving than straight pulls. Even a 1 mm misplacement of a hole can create a visual tilt. A drilling jig is worth the small investment if you’re installing more than a few.
• The finish leans a touch brighter in person than some product images suggest. If you’re seeking a very dark, antiqued bronze, this antique brass will read lighter and warmer.

Value

Individually, cabinet hardware can get expensive quickly. Buying in a 10-pack helps keep costs in check without stepping down to flimsy, stamped pieces. The Khtumeware cup pulls feel closer to boutique than bargain in hand, and the consistent finish makes them viable for larger kitchens where mismatches would stand out.

If you’re outfitting an entire room, having a dependable, consistent 3-inch option also makes it easier to pick companion pieces like knobs in similar finishes from other lines if needed.

Tips for a smooth install

• Measure twice, drill once. Confirm your centerline and handle height with painter’s tape before committing.
• Use a hardware jig to keep holes perfectly aligned; cup pulls amplify misalignment more than straight pulls.
• Pre-thread the screws into the pulls at your workbench; it’ll save you frustration at the cabinet.
• Hand-tighten for the final few turns to avoid stripping threads or cracking painted finishes.

Who they’re for

These cup pulls are a strong fit if you want to:

• Warm up a space with a classic profile and a contemporary brass tone.
• Refresh standard 3-inch hardware without redrilling existing holes.
• Get a cohesive, quality look on a realistic budget.

If your aesthetic leans industrial-black or you need a very dark oil-rubbed finish, you’ll likely prefer a different colorway. And if you’re allergic to precise measuring, consider a simpler pull style; cup pulls reward careful layout.

Recommendation

I recommend the Khtumeware cup pulls. They deliver solid build quality, a well-executed antique brass finish that works across a range of cabinet colors, and an easy upgrade path thanks to the 3-inch center spacing. Installation takes a bit of care, but with a basic jig and hand tools, the process is straightforward. The end result looks and feels more expensive than the price suggests, and the finish has held up nicely in daily use. If you’re looking for a tasteful, durable, and budget-savvy way to elevate your cabinets and drawers, these deserve a spot on your shortlist.