ADLMPW (20 Pack) 2" X 6" Joist Hanger 18 Gauge Double Shear Face Mount Joist Hangers for Wood, Floor Deck and Ceililng Joists

Why I reached for these hangers

I first put these 2x6 joist hangers to work on a small deck refresh and a shed floor rebuild—two jobs where consistent sizing, straightforward install, and corrosion resistance matter more than flashy branding. The pack-of-20 format made planning easy, and the 18‑gauge galvanized steel promised enough rigidity for typical residential spans with treated lumber. I’m picky about connector hardware: fit, hole layout, and how the hanger behaves during install are what determine whether a day goes smoothly or turns into a fight with misaligned steel. These hangers mostly stayed out of my way—and that’s a compliment.

What you get

• Quantity: 20 pieces
• Size: For nominal 2x6 joists (1‑1/2 in. x 5‑1/2 in.)
• Material: 18‑gauge galvanized steel
• Style: Double‑shear, face‑mount
• Built‑in tabs to temporarily hold the hanger during fastening
• No fasteners included

From the box, the hangers were clean, square, and consistently formed. I didn’t find bent flanges or crushed seats—important when you’re setting a lot of them in a row.

Build quality and corrosion protection

The 18‑gauge steel lands in that “gets it done” middle ground. These aren’t tank‑like, but they’re not flimsy either. They hold shape when you set a joist and don’t deform under normal nailing or screwing. Compared to premium, heavier‑coated options, the galvanization looks like a standard build—uniform and free of bare spots in my batch. For most exterior applications where the lumber is pressure‑treated and the exposure is typical (not continuously wet, coastal, or chemically aggressive), the coating should be fine if paired with compatible fasteners.

A couple of caveats:

• For marine/coastal environments, heavy salt exposure, or permanent wet service, I prefer a higher‑grade coating (G185) or stainless where code and durability demand it.
• Always match fasteners to the treatment chemicals in your lumber to avoid galvanic corrosion.

Edges had the usual punched‑steel sharpness; gloves are advised until they’re on the wall.

Fit and hole layout

Fit on nominal 2x6s was spot‑on. With occasional crowned or roughsawn boards, I had the expected minor variances, but the seat and side flanges accommodated without fuss. The double‑shear configuration (those angled holes that drive through the joist into the header) is the right call for better load transfer and less splitting than straight‑in nailing. The hole pattern gives enough options that I could work around knots or old hardware holes during a repair.

Hole sizing accepted common 0.148 in. x 1‑1/2 in. joist hanger nails. Structural screws designed for hangers also seated cleanly. I appreciated the extra holes—on a rehab where some old nails had rusted away, I could shift to unoccupied holes and still fill the pattern appropriately.

Installation experience

The built‑in support tabs are surprisingly helpful. They act like small prongs that bite just enough to hold the hanger against the header, letting you set one hand on the level and the other on a fastener. Working solo, that saves time. The tabs aren’t grabby enough to resist a hard bump, but they’re plenty for alignment and initial fastening.

A few practical notes from my installs:

• Layout: Snap clear, dark layout lines and set the first fastener with the hanger snug to your mark. These hangers don’t “self‑square,” so your first fasteners matter.
• Fasteners: Use rated joist hanger nails or structural screws; avoid drywall/deck screws. If you’re in exterior service with treated lumber, use hot‑dipped galvanized or appropriately coated structural screws.
• Sequence: Two face nails to tack, set the joist fully seated, then fill the double‑shear and remaining face holes.
• Tools: A palm nailer is your friend in tight bays; structural screws with an impact driver are cleaner in remodels where vibration matters.

Overall, installation was predictable and quick. I didn’t have to fight inconsistent tolerances or mispunched holes.

Performance in use

Once fastened, the hangers felt solid. Joists seated cleanly with no perceptible slop, and I saw no flange distortion under normal loads. On the deck refresh, the system tightened up the feel of the walking surface and eliminated the rattle I often see when older repairs rely on toe‑nails alone. On the shed floor rebuild, the hangers kept alignment consistent across the run—useful when you’re sheathing and want the edges to line up without shimming.

I can’t speak to precise load values because none were provided with the pack. In the field, though, they performed as an 18‑gauge 2x6 hanger should when properly fastened.

Code and compliance considerations

This is the section many buyers skip—and shouldn’t. For permitted structural work, inspectors typically want connectors with published load tables and an evaluation report (e.g., an ICC‑ES report). The hangers I received did not include published ratings or a report. That does not mean they’re weak; it means I can’t point to official values in a code context.

My approach:

• For permitted decks, structural repairs, or any project where an inspector will check connectors, I use hardware with a recognized listing and printed load tables.
• For non‑permitted projects, temporary structures, utility builds, or repairs where I’m not seeking a stamp, I’m comfortable using these when installed with proper fasteners and practices.

Always verify local code requirements—many jurisdictions are strict on connector listings.

Where these hangers make sense

• Budget‑sensitive projects that still demand consistent fit and easy install
• Sheds, small decks, porch framing, ceiling joists, and floor repairs where you need a reliable 2x6 connection
• Remodels where double‑shear holes help you work around existing damage

Less ideal:

• Coastal/marine work, continuous wet service, or highly corrosive environments without upgraded coating or stainless
• Any inspected project requiring listed load values and documentation

Pros

• Consistent fit for 2x6 lumber; clean forming with minimal variance
• Useful temporary support tabs for solo installs
• Double‑shear hole pattern improves connection quality and options
• Good value in a 20‑pack; straightforward to stage and deploy
• Galvanized finish is even and adequate for typical exterior use with compatible fasteners

Cons

• No published load tables or code listing included—can be a non‑starter for permitted work
• 18‑gauge is serviceable but not as rigid as heavier or premium connectors
• Edges are a bit sharp out of the box; handle with gloves
• Fasteners not included, so plan your nail/screw purchase

Tips for best results

• Pre‑sort joists by crown and seat the crown up; it reduces fighting the fit.
• Use a layout jig or spacer block for perfectly uniform hanger height across a run.
• Choose fasteners rated for hangers and compatible with your lumber’s treatment chemicals.
• Don’t skip the angled double‑shear fasteners; they’re key to the connection’s performance.

The bottom line

These 2x6 joist hangers deliver reliable everyday performance with a smooth installation experience. The build is consistent, the double‑shear pattern is thoughtfully laid out, and the temporary holding tabs shave real minutes off repetitive installs. While they don’t match the stiffness of heavier or premium alternatives, they’re absolutely up to the task for typical residential framing when paired with the right fasteners.

Recommendation: I recommend these hangers for budget‑conscious, small‑to‑medium projects where you don’t need published load tables or a specific code listing. If your project will be inspected or lives in a corrosive environment, opt for a listed hanger with documented load ratings and, if needed, heavier galvanization or stainless. For everything else, these are a practical, cost‑effective choice that install easily and hold up well.