VGBUY 180PCS Conical Concrete Anchors and Screws Assortment Kit, 90PCS Concrete Wall Anchors, 90PCS Self Tapping Screws for Masonry Stucco Brick Cement Cinder Block Tile, with 2PCS Drill Bit

I keep a small section of my drill case dedicated to anchors and screws for masonry jobs, and the VGBUY masonry anchor kit has been living there for the last few weeks. I used it across a mix of substrates—brick, stucco over block, and poured concrete—hanging utility hooks in the garage, mounting a hose holder outside, and fastening a light-duty shelf in a basement stairwell. It’s a straightforward kit, and that’s part of its appeal: two sizes of blue conical PE anchors, matching galvanized flat-head screws, and two drill bits to get you started.

What you get and how it fits together

The assortment is simple and sensible. There are 90 blue polyethylene anchors split between two sizes (#12–16 at 1.38" length and #10–12 at 1.06") and 90 self-tapping galvanized screws (30 × #10 at 1.58" and 60 × #8 at 1.18"). The anchors and screws pair up intuitively: the larger anchors with the longer #10 screws, and the smaller anchors with the #8 screws. The set arrives in a compartmented plastic box that keeps everything sorted.

These are classic conical expansion anchors: drill, tap the anchor in, and drive the screw to expand the anchor against the hole. The plastic is firm but not brittle, and the anchors don’t mushroom prematurely when hammered in properly. The screws are cleanly threaded, and the flat heads sit flush without chewing up the surrounding material. The galvanization is even, and none of the screws I used showed bent shanks or malformed tips.

The included drill bits are sized to the anchors, which removes guesswork. They’re passable for general masonry, especially mortar joints and typical cinder block. On hard, aggregate-heavy concrete, I found they dulled faster than my pro-grade carbide hammer bits. More on that below.

Installation in practice

For brick and mortar, I prefer drilling into the mortar joint when the application allows it—easier drilling, less risk to the brick face, and plenty strong for light-to-medium loads. In mortar, both bit sizes cut cleanly with a hammer drill, and the anchors seated with a couple of taps. On stucco, I drilled through the stucco skin and into the block behind; the small anchor size is nice here because it minimizes surface damage. In cinder block, I targeted the web rather than the hollow voids to ensure the anchor had material to expand against.

In poured concrete, the experience depends on the mix you’re facing. In a garage slab wall with harder aggregate, the included bit labored and glazed after a few holes; swapping to a fresh carbide hammer bit sped things up dramatically. That’s not unusual for bundled bits in kits at this price; I treat them as a convenience, not a long-term consumable.

A few practical notes from use:
- Pre-drill to full depth and clear dust periodically; vac or blow out the hole so the anchor seats fully.
- Stay back from edges and corners to avoid cracking.
- For stucco and tile, go slow at the surface to prevent chipping; the bits here aren’t tile-specific, so for porcelain or glass tile I’d reach for a dedicated tile bit first.
- In cinder block, avoid drilling into the hollow unless you’re using a toggle—these anchors need solid material.

Driving the screws with a low-impact setting on an impact driver worked well. I snugged them until the anchor bite was firm; overdriving can spin the anchor in a crumbly substrate.

Holding power and real-world expectations

The kit is rated up to 75 lb when pre-drilled and installed properly. In practice, that’s a best-case number in sound concrete with the larger size, and it assumes loads in shear with good edge distance. I treat these as light-to-medium duty. The garage utility hooks (drills, cords, a small blower) and a small hose holder have held up without any creep or play. For the basement shelf, I used four larger anchors into brick and was comfortable with the result because the shelf was shallow and lightly loaded.

Where I draw the line: heavy cabinets, cantilevered loads, dynamic loads, and overhead applications. For those, I’d use a sleeve anchor, a wedge anchor, or a concrete screw (e.g., a hardened masonry screw) sized appropriately, or move to an epoxy/set anchor system in questionable substrates. Plastic conical anchors have their place, but they’re not a one-size solution for everything masonry.

Materials and corrosion resistance

The PE anchors have the right balance of stiffness and expansion. They don’t split under moderate hammer taps, and they expand predictably when the screw is driven. The screws’ galvanization is appropriate for humid interiors and typical outdoor settings under cover. For coastal environments or consistently wet exposures, I’d step up to stainless hardware or fully coated masonry screws.

The flat-head design was helpful when mounting brackets and hardware that benefit from a flush finish. Drive recess quality was consistent, and I didn’t experience cam-out or stripping with a standard bit and sensible torque.

Where this kit shines

• Quick, tidy fixes: bathroom hooks, light shelves, hose holders, address plaques, cable clips, and small brackets in concrete, brick, stucco, and block.
• Mixed-material projects: you get two anchor and screw sizes that cover many common fixture holes without reaming hardware to fit.
• Occasional outdoor use: the galvanized screws resist corrosion well enough for general exterior tasks, provided they’re not immersed or sitting in water.

The variety in a single box reduces the back-and-forth to the hardware store. For a homeowner or a pro who wants a grab-and-go option for punch-list items, it’s practical.

Limitations and gotchas

• Only two anchor diameters: if you need anything beefier, you’ll want a larger-diameter anchor or a different anchor type altogether.
• Bundled drill bits: they work, but they’re consumables. In hard concrete, expect to switch to a heavier-duty carbide bit. They’re not tile bits.
• Substrate sensitivity: in old, sandy mortar or crumbly block, conical anchors can spin. If that happens, step up a size or change anchor types (sleeve, lead, or epoxy).
• Tile caution: while the kit mentions tile, I wouldn’t use these bits on porcelain. Pre-drill with a tile bit, then use the anchors once you’ve cleared the glaze.

Value and alternatives

As a value-oriented assortment, this kit makes sense. You get a balanced count—90 anchors, 90 screws, and two matching bits—in a compact box. If your work leans toward repeated heavy-duty fastening into concrete, you’ll be better served by hardened masonry screws (which don’t require plastic anchors) or mechanical anchors sized for the job. If you work primarily in hollow block or lath-and-plaster with large cavities, toggle or sleeve solutions may be more reliable.

That said, as an all-around “I need to mount a few things in masonry today” kit, it’s hard to argue with the convenience. The anchors behave predictably, the screws are consistent, and the included bits let you get started immediately.

Tips to get the most from the kit

• Use a hammer drill and a depth stop; consistent hole depth improves holding power.
• Clear dust before seating anchors; it makes a noticeable difference.
• Choose the largest anchor that fits your hardware’s clearance holes for better grip.
• For exterior use, add a dab of sealant around the hole to keep moisture out of the substrate.

Verdict

The VGBUY masonry anchor kit is a solid, no-nonsense assortment for light-to-medium duty fastening in concrete, brick, stucco, and block. The anchors expand reliably, the screws are well-finished and resist corrosion, and the two included drill bits are convenient starters, even if they’re not the last word in durability. It won’t replace heavier-duty anchors for demanding loads, and it’s not the ideal choice for porcelain tile or structural applications. But for everyday mounting tasks around a home or on a punch list, it’s exactly the kind of kit I like to keep on hand.

Recommendation: I recommend this kit for homeowners, handypeople, and pros who need a dependable, affordable set for common masonry fastening tasks. It’s versatile within its intended load range, organized, and easy to use. If your projects routinely involve heavy, dynamic, or overhead loads, pair this with a selection of larger mechanical or adhesive anchors and upgrade your drill bits for hard concrete.