Sakugi Storage Racks - 2 Pack, 5-Tier Freestanding Steel Shelving Units with Reinforced Frame, Adjustable Garage Organization Shelves for Warehouse, Basement, Workshop, 33.5" x 12.6" x 72", Black

Overview

If your garage, basement, or pantry is starting to sprawl, a pair of slim, tall racks can be a quick win. I set up the Sakugi 5‑tier racks as a two‑pack to tackle a mix of tools, paint, pantry overstock, and seasonal bins. They’re compact enough to fit along a wall without eating into floor space, but tall and configurable enough to make meaningful use of vertical real estate. After a few weeks of use and a couple of reorganizations, I have a clear sense of where these racks excel—and where they don’t.

Build quality and design

Each rack measures roughly 33.5 inches wide by 12.6 inches deep by 72 inches tall. That depth is a key part of the story. At 12.6 inches, these are decidedly slim shelves, closer to pantry or closet depth than a traditional garage unit. The upside is they’re easy to tuck into tight spaces and don’t jut out into walkways. The downside is obvious too: oversized totes, bulky bench tools, or deep appliances may not fit comfortably.

The frame uses 0.9‑inch diameter metal tubes with a protective coating. The finish on my set was consistent—no rough welds, sharp edges, or mismatched paint—and it’s held up fine in a slightly damp basement corner. The wire shelves are reinforced; they don’t feel flimsy, and the geometry resists torsion better than budget wire units I’ve used. As with any wire shelf, small items can tip or snag in the grid, so I used inexpensive plastic liners and a bit of 1/4-inch plywood on a couple tiers to create flat surfaces for jars and hardware organizers.

Four adjustable feet per rack provide a welcome degree of leveling. On my sloped garage slab, dialing in the feet took just a minute and completely eliminated rocking before anchoring. Sakugi includes wall‑fixing brackets, and given the height-to-depth ratio, I consider anchoring mandatory if you plan to store anything heavy or if the rack is in a high-traffic area.

Assembly experience

Assembly is straightforward. All hardware is labeled, the instructions are clear, and the design uses screw connections rather than press‑fit collars. I built each rack solo in under an hour using just a Phillips screwdriver; a ratcheting driver speeds things up and makes the repetitive steps easier on the wrist.

A few tips from my build:

• Assemble loosely at first. Get the frame together with all screws started, square everything up, and then do your final tightening.
• Set your shelf spacing on the floor using the items you plan to store as a guide. I staged a couple of bins and tool cases to find a sensible rhythm (tighter spacing higher up, wider at the bottom).
• Anchor into studs. The included brackets are useful, but for real security, sink them into wood, not drywall alone.

Overall, the parts lined up, no holes were misdrilled, and there were no mystery pieces left over. It’s an approachable project for one person with basic tools.

Capacity and stability

Sakugi rates each rack at up to 1,000 pounds with the load evenly distributed. That caveat matters with any shelving, and doubly so with wire decks: concentrated loads can create early sag. With weight spread across the grids and heavier items placed on the lower tiers, the racks feel secure. I loaded one unit with paint cans, a compact compressor, and a few tool cases; the other became a pantry overflow with bulk dry goods, small appliances, and cleaning supplies. No creaks, tilts, or visible deformation, and the frames didn’t twist when nudged.

Left freestanding and empty, the tall, narrow footprint can feel a bit tippy. Once loaded and anchored, side‑to‑side movement drops to a non-issue. The adjustable feet are precise enough to eliminate wobble on uneven floors. I wouldn’t treat these as industrial racking—no bench grinders on the top shelf or anvils on mid-tiers—but for typical home and light workshop use they’re reassuringly stable.

Day‑to‑day use

The dimensions and adjustability make these racks particularly useful in a few scenarios:

• Pantry or laundry: Slim depth keeps passageways clear, and the wire shelves allow airflow around linens or supplies. Plastic liners help with small bottles and jars.
• Workshop wall: Great for tool cases, organizers, spray cans, and fastener bins. I ran a power strip behind one unit for battery chargers and tucked chargers on a mid-tier.
• Basement storage: Seasonal decor, smaller totes, and home maintenance supplies. For larger bins, you’ll wish for deeper shelves.

I appreciate the finish; dusty racks are easy to wipe down with a damp cloth, and I haven’t seen any surface rust in a humid area. The black color also blends rather than draws attention—a nice touch in a multipurpose room.

One thoughtful detail: the racks don’t eat up much visual space. In cramped rooms, that matters. Two units side‑by‑side essentially create a 5.5‑foot wide, 6‑foot tall storage wall that’s tidy and organized without the bulk of a traditional 18‑inch deep garage rack.

Limitations and trade‑offs

• Depth: At 12.6 inches, you’ll need to measure your bins and appliances. Many 17–27 gallon totes won’t sit fully supported front‑to‑back. If large totes are your primary storage, look elsewhere.
• Wire shelf behavior: Small feet on appliances or narrow box edges can catch in the grid. Liners or plywood panels solve this but are an extra step.
• Heavy point loads: While the frames feel robust, wire shelves are not ideal for concentrated loads. Spread weight and keep the heaviest items on the bottom tiers.
• Hardware pace: Screw‑together builds are secure, but they take longer than snap‑sleeve systems. Not a big deal, just plan a bit of time.

None of these are deal‑breakers given the category, but they’re worth considering based on your storage plan.

Who it’s for

• Homeowners seeking slim, tall storage along a wall or in a closet, pantry, or laundry.
• Renters who want freestanding racks that can be anchored non-destructively into studs and removed later.
• Hobbyists and DIYers organizing tools, bins, and consumables without dedicating deep floor space.

Who should look elsewhere:

• Anyone prioritizing storage for large totes, deep appliances, or large bench tools—opt for 18–24 inch deep shelving instead.
• Users needing industrial‑grade racking and unfussed heavy point loads.

Tips for getting the most out of it

• Plan your shelf heights with what you own. Tall shelves are tempting but waste vertical space if you don’t need the clearance.
• Use liners on the top two tiers where you’re likely to put smaller items; leave lower tiers open for airflow around paint or chemicals.
• Anchor at two points if possible, especially in quake‑prone regions or households with kids or pets.
• Label shelves after you settle on a layout. It sounds tedious, but it cuts down on the impulse to overstack random items.

Value and alternatives

As a two‑pack, these racks make it easy to standardize storage across a wall. You could pay more for deeper, NSF‑style chrome wire shelves, or less for particleboard units that won’t like moisture. The Sakugi pair sits in a practical middle ground: metal, moisture‑resistant, and adjustable, with a trim footprint that suits real homes. If your use case aligns with the depth and you’re fine with wire decks, it’s a compelling value.

Verdict

The Sakugi 5‑tier racks hit a sweet spot for compact, adjustable, and stable household storage. They’re easy to assemble, look clean, and feel sturdier than bargain wire shelving, especially once leveled and anchored. The shallow depth is both their biggest strength and their clearest limitation—excellent for tight spaces and everyday items, less ideal for bulky totes or heavy, concentrated loads.

Recommendation: I recommend these racks to anyone who needs slim-profile metal shelving for garages, basements, pantries, or workshops where floor space is at a premium. They’re durable, straightforward to set up, and flexible enough to evolve with your storage needs. If your storage revolves around large totes or heavy bench tools, choose a deeper, industrial rack; otherwise, this two‑pack is an efficient, tidy upgrade that’s easy to live with.