Lanties 5 Pieces Airless Paint Sprayer Tip Extension Pole Extension Rod for Airless Painting Spray Gun with Red Guard

Why I reached for this extension set

I spend more time than I’d like climbing ladders with a sprayer in hand. It’s not just inefficient—it’s awkward and fatiguing. That’s why I gave the Lanties extension set a proper workout on a few recent jobs: a 10-foot interior ceiling repaint, a stairwell with high runs, and a barn exterior where reach matters. The promise is simple: five aluminum extension poles, all with 7/8-inch threads to fit most airless spray guns, plus a red tip guard. Different lengths let you pick the right reach without fighting a pole that’s either too short or annoyingly long.

What you get

• Five aluminum-alloy extensions: 7.87", 11.81", 19.69", 29.53", and 39.37"
• Standard 7/8" threaded ends
• A red guard for your tip assembly
• Lightweight, anodized finish

Each piece feels light but not flimsy. The lengths are genuinely useful; the 30-inch became my default for 9–10 foot ceilings, the 20-inch was perfect for upper wall sections and soffits, and the 40-inch made quick work of high beams and the barn’s upper runs. I never felt the need to “make do” with an awkward length.

Setup and compatibility

All five extensions threaded cleanly onto my airless gun (7/8" thread) and the included red guard accepted my standard tip assembly without drama. I started each connection by hand to avoid cross-threading, then snugged it with a wrench. That last step matters. At airless pressures, even a small misalignment or loose fit can weep paint. With a firm, properly aligned connection, these sealed up well.

A note on compatibility: these follow the common 7/8" thread standard found on most North American airless spray guns and tip guards. If your gear uses a different standard, you’ll want to confirm before buying.

In use: control, reach, and spray quality

• Control: The shorter extensions (8" and 12") feel like part of the gun—minimal added leverage, very precise around trim and transitions. The 20" and 30" lengths strike the best balance for ceilings and tall walls. The 40" does introduce some front-heaviness, but with two hands and a steady pace, it’s entirely manageable.

• Reach: These eliminate a lot of ladder work. On the 10-foot ceiling, the 30" extension let me walk and spray at a consistent standoff distance with my feet on the floor. On the barn, switching to the 40" length let me spray under eaves and higher siding without continually moving platforms. That alone saves serious time.

• Spray quality: I didn’t see pattern distortion or unusual tailing attributable to the extensions. The internal diameter seems adequate; at typical pressures for wall and ceiling work, I noticed no meaningful pressure drop. If you’re pushing thick coatings through larger tips at the longest length, you may need to bump pressure slightly—but that’s normal with any extension.

Build quality and durability

The aluminum alloy bodies are light and don’t flex excessively, even at 40". The finish resists scuffs reasonably well; mine picked up a few cosmetic scratches but nothing that affects function.

Thread machining is decent but not bulletproof. On two pieces, the threads felt a touch shallow compared with more expensive OEM rods, which makes it easier to cross-thread if you’re careless. Start every connection by hand, ensure the threads are square, then tighten with a wrench. Do that and you’ll be fine.

Sealing is generally good. I had a minor weep on the shortest (about 8") extension during first use. It turned out to be a slightly rough seat. A quick cleanup, a fresh O-ring, and a firmer wrench snug solved it. None of the longer rods leaked after proper tightening.

Ergonomics on longer runs

Weight is a clear advantage here. Compared to steel or heavier-duty rods, these extensions reduce shoulder fatigue over long passes. That matters when you’re doing multiple rooms in a day. The 40" is the only one that felt slightly “whippy” when moving too fast across wide spans; slowing to a controlled pace and using both hands (one on the gun, one stabilizing the extension) kept it steady.

For stairwells and high wall cut-ins, the 20" and 30" lengths really shine. They keep your nozzle where it needs to be without forcing awkward wrist angles or a stair ladder shuffle. My productivity uptick was noticeable, and my back thanked me later.

The included red guard

The guard is basic but functional and threads on cleanly. It held my tips securely and provided the expected standoff protection. If you already own a preferred guard system, you can keep using it; the extensions are the star here.

Practical tips from the field

• Always start threads by hand. Aluminum will lose a fight with steel if you force a misaligned start.
• Wrench snug—not gorilla-tight. Firm, consistent torque is enough to seal without chewing threads.
• Check O-rings before first use. Keep a couple spares in your kit. They’re cheap insurance.
• Keep your standoff consistent. Extensions make it easy to drift a bit farther from the surface; watch your overlap and speed to avoid light bands.
• Don’t overreach with the longest rod in cramped spaces. Drop to the 20" or 12" for better control around lights, returns, and transitions.

Where these shine—and where they don’t

• Best use cases:

  • Ceilings and high walls in standard-height homes
  • Stairwells and two-story foyers
  • Exterior siding, soffits, fascia, and barn walls
  • Repetitive production work where staying off ladders saves time

• Limitations:

  • If your gun or guard doesn’t use 7/8" threads, you’ll need an adapter or a different set.
  • The longest rod demands good technique to avoid wobble on fast lateral passes.
  • Thread depth isn’t as robust as premium OEM extensions; care during setup matters.

Value and alternatives

Compared to brand-name single-length extensions, this five-piece set offers strong value. You get a sensible spread of lengths for less than what two or three OEM pieces might cost. The trade-off is in the details—shallow-ish threads on a couple pieces and slightly less refined machining. In practice, those didn’t stop me from getting clean, efficient results, but they’re worth acknowledging if you’re outfitting a crew that’s hard on gear.

If you’re spraying daily in a commercial environment, premium steel-bodied extensions can take more abuse and may thread more smoothly over years of use. For homeowner projects, small contractors, or anyone who wants multiple reach options without overspending, this set hits a sweet spot.

Final thoughts

The Lanties extensions did exactly what I needed: they kept me off ladders, improved my pace, and didn’t compromise finish quality. I appreciated the five lengths more than I expected—being able to switch to the just-right reach kept my standoff distance consistent and my lines cleaner. Aside from a minor weep on the smallest rod that a new O-ring and proper tightening fixed, the set performed reliably across interior and exterior work.

Recommendation: I recommend this set for painters who want versatile reach options at a reasonable price and are willing to be a bit mindful during setup. If you start threads carefully, snug connections with a wrench, and keep an eye on O-rings, these aluminum extensions deliver solid performance without adding weight or hassle. For heavy-duty, every-day commercial abuse, you might prefer pricier OEM rods—but for most projects, this set is a smart, practical upgrade that saves time and strain.