WIESVOP Garden Hose Shut Off Valve, 2 Pack Heavy Duty 3/4 Inch Solid Brass Water Hose Connector Hose Shut Off with 4 Extra Rubber Washers

Why I added brass shutoff valves to every hose I own

A shutoff valve is one of those small accessories that quietly makes everyday watering easier. I started using this brass shutoff valve on a few different hoses—one at a back patio spigot, one out by garden beds, and another on a hose reel—and it hasn’t left my setup since. The combination of solid-brass construction and a big, grippy handle makes a noticeable difference when you’re trying to control flow at the end of a hose without walking back to the faucet.

Build and design

These are compact, inline quarter-turn valves designed for standard 3/4-inch garden hose threads (GHT). The body is solid brass, which matters for two reasons: it resists corrosion from outdoor exposure, and it holds its threads over time better than plastic or pot-metal fittings. The bore through the valve feels appropriately sized for typical hose work; fully open, I didn’t notice any meaningful restriction in flow.

The handle is a large plastic lever with a slightly rubberized feel and gentle contour. I prefer this over small metal paddles because you can operate it with wet hands or gloves without slipping. The lever turns 90 degrees from fully closed to fully open, with clear stops at each end so you’re never guessing. It also gives you precise control when you want partial flow—handy for delicate watering or filling containers without splashback.

Each pack includes two valves and four spare rubber washers. These are standard flat hose washers that seal at the female end. It’s a small inclusion, but it saves a run to the hardware store and helps you keep a tight seal if a washer goes hard or vanishes mid-season.

Installation and setup

Installation is straightforward:
- Thread the female end of the valve onto the spigot or the male end of your hose.
- Drop a washer into the female side if it isn’t already seated.
- Hand-tighten until snug. You don’t need thread tape—garden hoses seal at the washer, not the threads.
- Attach your hose or accessory to the other end and snug it by hand.

On my initial install, both valves sealed without leaks using only hand pressure. If you see a drip at the female side, check the washer: make sure it’s seated flat and in good condition. The included spares are exactly the kind of backup you’ll want in a garden drawer.

I also liked how compact the valves are. They didn’t crowd neighboring connections on a two-way splitter, and they fit fine on a hose reel without bumping the frame.

Everyday performance

• At the spigot: With a valve parked at the faucet and the hose left pressurized, I can swap spray nozzles or sprinkler heads without slogging back to the wall. The lever makes a clean, quick shutoff—no endless twisting.
• At the hose end: For planters, partial flow is smooth with decent granularity; it’s easier to set a gentle stream than with many twist nozzles.
• With sprinklers: Fully open, I didn’t see any drop in throw distance versus a bare hose. The valve doesn’t appear to bottleneck average residential pressure.
• On a hose reel: The brass body adds a little weight but not enough to stress the fitting. The lever position clears the reel frame on the models I tried.

The valve action is firm and consistent with a bit of resistance that reassures rather than annoys. It’s not floppy, and it hasn’t loosened over a few months of frequent use.

Durability and weather

Brass is a good choice for fittings that live outdoors. It shrugs off rain, irrigation splash, and the accidental drop on concrete. After extended use, the body shows only the expected patina; threads remain crisp and clean. The handle, being plastic, stays cool in direct sun, which is a real benefit on hot days when metal parts can burn fingers. That said, plastic can get brittle after years of UV exposure. I can’t speak to multi-year aging yet, but storing the hose out of direct sun or under a reel cover should prolong the handle’s life.

Cold-weather note: Like any valve, it can trap water. If you’re in a freeze zone, open the valve when you winterize and store it in a frost-free space. Brass can crack if water freezes inside.

Compatibility and use cases

These fit standard 3/4-inch garden hose threads found on:
- Outdoor spigots
- Hose-end nozzles and wands
- Lawn sprinklers
- Hose splitters and timers
- RV/camper connections and marine washdowns

I’ve used the valves both at the source and downstream. At the spigot, they neatly isolate a single hose from a splitter so I can turn one line off without interrupting a timer on the other. At the hose end, they make a simple nozzle even more useful by letting me fine-tune flow without constantly adjusting the nozzle head.

What I like

• Solid brass body that resists leaks and thread wear.
• Big, grippy handle for easy quarter-turn operation, even with gloves.
• Smooth flow control from trickle to full blast.
• Standard GHT compatibility across typical lawn and garden gear.
• Two-pack value and the inclusion of spare washers.
• No noticeable performance penalty when fully open.

What could be better

• The plastic handle is comfortable, but long-term UV exposure can age plastics; sheltering it will help.
• The added weight of brass is a net positive for durability but can tug slightly on lightweight hose-end accessories if you let the hose dangle from the nozzle.
• As with most hose valves, it relies on the condition of the flat washer for a good seal; keep a spare on hand (thankfully, they’re included).

None of these are deal-breakers; they’re just practical notes from daily use.

Tips for best results

• Hand-tighten only. If you feel the urge to wrench it, check the washer instead.
• Keep a couple of the included washers somewhere obvious—taped inside your hose reel lid or in a small zip bag near the spigot.
• If you want to relieve stress on a hose-end sprayer, add a short leader hose between the valve and the sprayer so the valve isn’t acting as a lever arm.
• Open the valve fully when feeding sprinklers or pressure-sensitive accessories to avoid unnecessary restriction.

Value

Getting two valves and four washers in a single package hits a sweet spot. I find it’s most useful to have at least two in play: one parked at the spigot and another at the hose end. The brass build and clean machining put these a cut above bargain-bin aluminum or plastic valves that tend to cross-thread, seize, or leak after a season.

Final take

This brass shutoff valve is the kind of small upgrade that pays off every time you turn on a hose. The build inspires confidence, the handle is genuinely easy to use, and the flow control is smooth enough to replace constant nozzle fiddling for many tasks. After using them across different hoses and attachments, I haven’t run into leaks or noticeable flow loss, and the fittings still spin on and off cleanly.

Recommendation: I recommend these shutoff valves for anyone who uses garden hoses regularly and wants reliable, one-handed control at either end of the line. They’re durable, easy to operate, broadly compatible, and the two-pack with extra washers delivers practical value. If you protect the handle from harsh UV and winterize properly, I expect them to outlast cheaper alternatives and simplify everyday watering.