Bullbins Paper Towel Holder for Pegboard, Extendable, Fit Any Standard Pegboard, Peg Board Organization Accessory Hook for Workshop, Garage, Kitchen, Laundry Room, Bathroom 2 Packs, Black

Why I added another pegboard accessory

Pegboard space is prime real estate in my shop, and I’m picky about what earns a permanent spot. I picked up the Bullbins pegboard paper towel holder because I wanted a simple way to keep shop towels within reach and get a couple rolls of masking tape off my bench. After a few weeks of moving it around my garage and laundry area, I have a good feel for where this holder works well—and where it doesn’t.

Setup and fit

Installation is dead simple. Each holder has a pair of hooks that drop into standard pegboard holes, and the crossbar extends to accommodate different roll widths. I tried it on both 1/4-inch MDF pegboard and thinner metal pegboard with smaller holes. On the thicker board, the hooks seated snugly and the holder felt secure during use. On thinner metal pegboard, it still worked, but there was a little more play; a couple of pegboard locking clips or even a zip tie through one of the holes made it rock-solid.

The extendable bar gives it some useful flexibility. For me, it comfortably handled typical shop towel rolls and most standard kitchen paper towels. Extra-large, jumbo kitchen rolls were a tight fit and occasionally rubbed the support arms. If you’re buying it specifically for jumbo rolls, you’ll want to measure your typical roll diameter and compare—there’s a sweet spot here, and it’s more small-to-medium than oversized.

Build quality

The Bullbins holder is made from lightweight metal with a black coating. The finish on my set was even and didn’t flake with normal use. The wire gauge isn’t heavy-duty—think “utility hook” rather than “bar stock”—but it’s adequate for the loads this accessory is intended to carry. I did tweak one arm slightly to square it up after unboxing; a gentle bend fixed it in seconds. Once mounted, there was minor flex when I loaded it with several rolls of tape, but not enough to cause concern.

The lightweight build cuts both ways: it won’t sag under a paper towel roll, but it’s not designed for heavy spools of wire or a stack of duct tape. Keep expectations in line with the form factor and you’ll be fine.

Everyday use

As a towel dispenser, the holder is straightforward. There’s no serrated edge or tension mechanism, so tearing a sheet cleanly depends on the perforation and your technique. I had the best luck pulling slightly upward and toward the wall with one hand, then tearing against the roll. On a stiff, perforated shop towel, I could often do it one-handed. With softer kitchen towels, I needed a second hand more often than not—normal for most open-rod holders.

One quirk of the design: swapping rolls requires lifting one side out of the pegboard to slide the bar free. It’s not a hassle, but it’s not a spring-loaded, one-click swap either. If you change rolls constantly, this will be noticeable. For occasional changes, it’s a minor trade-off for the simplicity.

Capacity and compatibility

• Paper towels: Best with standard-size rolls. Jumbo or “mega” rolls fit inconsistently and may rub the arms until they’re partially used.
• Shop towels: Excellent fit; they’re narrower and stiffer, and the holder handles them well.
• Toilet paper: Overkill, but yes, it works for compact spaces where a tiny roll is all you need.
• Tapes and spools: Painter’s tape, masking tape, and small ribbon or heat-shrink spools work great. A couple of rolls of duct tape are fine. Heavy wire spools are pushing it.

Because there’s no integrated friction, lightweight rolls can freewheel if you yank hard. An easy fix is to add a small rubber O-ring or a wrap of electrical tape near the ends of the bar to introduce a hint of drag. It’s a $0.10 improvement that noticeably helps with clean tears.

Beyond paper towels

The two-pack is the real value here. I mounted one by my bench for shop towels and repurposed the second as a tape organizer. Sliding rolls of painter’s tape and electrical tape onto the bar freed a drawer and made it obvious which sizes I was low on. I also used it briefly for 5-inch sanding discs on a center core I printed—worked well until I moved to a drawer system.

If you’re a crafter or sewist, the holder doubles as a tidy ribbon dispenser. In a garden shed, it’ll keep twine and small tie wire at the ready. Just keep the weight reasonable and it behaves.

Convenience trade-offs

• Roll changes require lifting one side off the board. Simple, but not instant.
• No built-in tension. Works fine with good perforations; add a bit of DIY friction if you want cleaner tears.
• Light-gauge metal. Stable on proper pegboard, but not designed for heavy loads.

None of these are deal-breakers for the intended use, but they’re worth knowing so you can set the holder up for success.

Tips for best results

• Lock it down: Use pegboard clips, a zip tie, or a small screw-in peg lock to eliminate wobble, especially on thin boards.
• Add friction: A pair of rubber O-rings or a wrap of tape on the bar keeps rolls from over-spinning.
• Mind the roll size: If you prefer jumbo kitchen rolls, mount this for shop towels and use a different dispenser for the kitchen.
• Positioning matters: Place the holder at shoulder or chest height with clearance on one side so you can pull and tear naturally.

Durability and maintenance

After several weeks, the finish still looks new and the arms haven’t deformed. Paper dust and shop debris wipe off easily. Because there are no moving parts beyond the sliding bar, there’s not much to fail. If the bar ever gets sticky, a quick clean and a touch of paste wax makes extension smooth again.

Who it’s for

• People who already use pegboard and want a simple, movable towel station.
• Makers who want a minimal, visible home for tape rolls and small spools.
• Anyone who prefers a clean, open-bar dispenser over enclosed wall-mounts.

Who should look elsewhere? If you need one-handed, on-demand towel tearing with a cutting edge, or you exclusively buy jumbo rolls, a wall-mounted dispenser with a spring-loaded bar or integrated brake will serve you better.

The bottom line

The Bullbins pegboard holder is a straightforward accessory that does what it says: it gets paper towels (or lightweight rolls) off your work surface and onto your pegboard without drama. It’s lightweight, easy to place and move, and the two-pack makes it versatile. The trade-offs—no tensioner, occasional need to unhook a side for roll changes, and a preference for standard rather than jumbo rolls—are real but manageable.

Recommendation: I recommend this holder for anyone with pegboard who wants a simple, affordable way to keep standard paper towels, shop towels, or light rolls within reach. It’s not a heavy-duty or premium dispenser, but for everyday use in a garage, workshop, or utility area, it earns its space and delivers solid value—especially as a two-pack. If you need effortless one-handed tearing or rely on oversized rolls, consider a different style; otherwise, this is an easy upgrade to a more organized bench.